User manual LG L1960TQ

[. . . ] User's Guide L1760TQ L1960TQ L1760TG L1960TG L1760TR L1960TR L1960TC Make sure to read the Important Precautions before using the monitor. Keep the User's Guide(CD) in an accessible place for furture reference. See the label attached on the monitor and give the information to your dealer when you ask for service. Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national standards if not being provided by the supplier. If the power cable is faulty in any way, please contact the manufacturer or the nearest authorized repair service provider for a replacement. [. . . ] Do not carry the monitor upside down holding only the stand base. The monitor may fall and get damaged or injure your foot. A3 Connecting the Display To attach or separate the back cap 1. To attach the back cap, fix into the 3 holes first then slide it up to fit to the upper groove. Back Cap NOTE - Cover the back cap after connecting the cables before use. (To connect the cable, see page A5 for reference. ) 2. To separate the back cap, hold the bottom part and pull it out. Kensington Security Slot Connected to a locking cable that can be purchased separately at most computer stores A4 Connecting the Display Connecting with the PC 1. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. When attached, tighten the thumbscrews to secure the connection. Connect the power cable 3 with the AC-DC adapter (AC-DC power supply) 2 , and then plug the cable in the outlet. 2. Connect the signal cable NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. DVI-D DC-IN D-SUB [ Arranging the cables] 3 2 DVI-D DC-IN D-SUB Wall-outlet type 1 PC DVI-D(This feature is not available in all countries. ) PC [ Connecting the cables] Mac adapter MAC For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector. 4. Touch the power button in front to turn on the monitor. The 'Self Image Setting Function' will automatically run when the monitor is on. (Only Analog Mode) NOTE ` Self Image Setting Function'?This function provides the user with optimal display settings. When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals. When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted screen while using the device or after changing screen resolution, press the SET/AUTO function button to improve resolution. A5 Control Panel Functions Front Panel Controls Side MENU SOURCE SET/AUTO Engine SET/AUTO Control MENU Button Function Use this button to enter or exit the On Screen Display. OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear. You can unlock the OSD controls at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" should appear. + - Buttons + Button Use these buttons to select or adjust functions in the On Screen Display. Use this button to make D-Sub or DVI connector active. (SOURCE Hot key) This feature is used when two computers are connected to the display. The default setting is D-Sub. - Button ( ) For more information, refer to page A13. A6 Control Panel Functions Control SET/AUTO Button Function Use this button to enter a selection in the On Screen Display. [. . . ] · Press the SET/AUTO button to automatically adjust your display image to the ideal setting. If the results are unsatisfactory, adjust the image position using the H position and V position icon in the on screen display. · Check Control Panel --> Display --> Settings and see if the frequency or the resolution were changed. If yes, readjust the video card to the recommend resolution. [. . . ]