User manual LG L1972H-PF

[. . . ] If shipped to USA/Canada, install only a UL LISTED/CSA LABELLED power supply cord meeting the following specifications: SPECIFICATIONS Plug Type Nema-Plug 5-15p Cord Type SVT or SJT, minimum 3 × 18 AWG Length Maximum 15 feet Rating Minimum 7 A, 125 V WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. Dangerously high voltages are present inside the unit. Refer servicing to qualified personnel only. FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] These settings may have to be repeated if you change the input signal after reconnecting your computer. 7 Press the m/M buttons until the horizontal stripes are at a minimum. GB Adjust so that the horizontal stripes are at a minimum. 8 Press the OK button. The main menu appears on the screen. If vertical stripes are observed over the entire screen, adjust pitch by the following steps. x Make further automatic adjustments to the picture quality for the current input signal (AUTO) 1 Press the MENU button. The main menu appears on the screen. 9 Press the m/M buttons to select PITCH and press the OK button. The PITCH menu appears on the screen. 2 Press the m/M buttons to select (SCREEN) and press the OK button. The SCREEN menu appears on the screen. 10 Press the m/M buttons until the vertical stripes disappear. 3 Press the m/M buttons to select AUTO and press the OK button. Make the appropriate adjustments of the screen's phase, pitch and horizontal/vertical position for the current input signal and store them. 4 Press the m/M buttons to select button. Return to the menu screen. and press the OK Adjust so that the vertical stripes disappear. 11 Click [END] on the screen to turn off the test pattern. 13 12 Press the OK button. Return to the SCREEN menu. 13 Press the m/M buttons to select button. Return to the menu screen. and press the OK Adjusting the color temperature (COLOR) You can select the color level of the picture's white color field from the default color temperature settings. Also, if necessary, you can fine tune the color temperature. x Adjust the picture's position manually (H CENTER/V CENTER) If the picture is not in the center of the screen, adjust the picture's centering as follows. 1 Press the MENU button. The main menu appears on the screen. 1 Set the resolution to 1280 × 1024 (L1972H-PF/ SDM-S94) on the computer. 2 Press the m/M buttons to select (COLOR) and press the OK button. The COLOR menu appears on the screen. 2 Load the CD-ROM. 3 Start the CD-ROM, select the region and model, and display the test pattern. For Windows Click [Utility] t [Windows]/[Win Utility. exe]. Press the m/M buttons to select (INPUT SENSING) and press the OK button. The INPUT SENSING menu appears on the screen. 0 Resetting the adjustment data to the defaults (RESET) Reset the adjustments to the default settings. 2 1 Press the MENU button. The main menu appears on the screen. 2 Press the m/M buttons to select 0 (RESET) and press the OK button. The RESET menu appears on the screen. 3 Press the m/M buttons to select the desired mode and press the OK button. · OK: To reset all of the adjustment data to the default settings. Note that the (LANGUAGE) setting will not reset by this method. · CANCEL: To cancel resetting and return to the menu screen. 15 Locking the menus and controls (MENU LOCK) Lock the control of buttons to prevent accidental adjustments or resetting. Technical Features Power saving function This monitor meets the power-saving guidelines set by VESA, ENERGY STAR, and NUTEK. If the monitor is connected to a computer or video graphics board that is DPM (Display Power Management) Standard compliant, the monitor will automatically reduce power consumption as shown below. 1 Press the MENU button. The main menu appears on the screen. 2 Press the m/M buttons to select (MENU LOCK) and press the OK button. The MENU LOCK menu appears on the screen. L1972H-PF Power mode normal operation active off* (deep sleep) power off Power consumption 45 W (max. ) 1. 2 W (max. )** 1 W (max. ) 1 (power) indicator 3 Press the m/M buttons to select ON or OFF and press the OK button. · ON: Only the 1 (power) switch will operate. If you attempt any other operation, the (MENU LOCK) icon appears on the screen. If (MENU LOCK) has been set to ON, when you press the MENU button, (MENU LOCK) is automatically selected. green orange red off main power off 0 W SDM-S94 Power mode normal operation active off* (deep sleep) power off Power consumption 50 W (max. ) 1. 2 W (max. )** 1 W (max. ) 1 (power) indicator green orange red off main power off 0 W * When your computer enters the "active off" mode, the input signal is cut and NO INPUT SIGNAL appears on the screen. [. . . ] The relevant TCO'99 demand requires that plastic components weighing more than 25 grams must not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed circuit boards since no substitutes are available. x Congratulations! You have just purchased a TCO'99 approved and labelled product!Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products. x Why do we have environmentally labelled computers? In many countries, environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment. [. . . ]