User manual LG L1982U

[. . . ] User's Guide L1982U Make sure to read the Important Precautions before using this product. Keep the User's Guide (CD) in an accessible place for future reference. See the attached label on the unit and show this information to your dealer when asking for service. Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national standards if not being provided by the supplier. If the power cable is faulty in any way, please contact the manufacturer or the nearest authorized repair service provider for a replacement. [. . . ] Press the button on the front switch panel to turn the power on. When the power is turned on, the 'Self Image Setting Function' will launch automatically. (Only Analog Mode) NOTE ` Self Image Setting Function'?This function provides the user with optimal display settings. When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals. When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted screen while using the device or after changing screen resolution, press the AUTO/SET function button to improve resolution. A6 Using the Auto Pivot and Auto Mirror functions This model supports Auto Pivot (automatic rotation) and Auto Mirror (automatic up/down reverse) functions. To use these functions, first install the provided Forte Manager software, and then set to Automatic. (Manual is the default setting when you initially purchase the product. ) - Refer to the installation guide, which is included on the CD for more details on the installation -To set to Automatic, select Forte Manager -> Option -> Pivot -> Enable Auto Pivot. Notice The Forte Manager software requires Microsoft Explorer 6. 0 or later. When the Auto Mirror function is engaged, the direction of the OSD (On Screen Display) menu will not change if it is rotated by 180°. (See the figure below) The response time (speed) for the Auto Pivot and Auto Mirror functions may vary depending on the video card and the PC's performance, None of these functions is supported in DOS mode. Update the video card driver on your PC to the latest version when the Forte Manager does not work properly or is out of order. Auto Pivot Screen rotation : You can rotate the monitor clockwise by 180 degrees. Caution : Do not touch the screen while you rotate the panel. This rear view represents a typical model. Your display model may differ from the illustration below. <Pushing the screen backwards> <Rotating clockwise> <When rotated by 90 degrees> <When rotated by 180 degrees> Tilt the screen while rotating it so that the monitor does not touch the floor. Do not hold the screen area as shown in the picture when rotating it, otherwise your fingers might get hurt or get stuck. Refer to the next page for Auto Mirror function. A7 Using the Auto Pivot and Auto Mirror functions <Pushing the screen backwards> <Rotating clockwise> <When rotated by 180 degrees> Tilt the screen while rotating it so that the monitor does not touch the floor. Do not hold the screen area as shown in the picture when rotating it, otherwise your fingers might get hurt or get stuck. Auto Mirror Screen switch : The monitor screen is automatically reversed when you switch it forward/backward as shown in the figure. Caution : Do not touch the screen while you rotate the panel. This rear view represents a typical model. Your display model may differ from the illustration below. Tip If you activate the Auto Pivot or the Auto Mirror function while the screen is almost level, the screen may not work properly. In this case, set the screen upright and adjust it to the proper angle. It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. A8 Control Panel Functions Front Panel Controls Bottom Control MENU Button Function Use this button to enter or exit from the On Screen Display. OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that these settings are not inadvertently changed. To lock the OSD settings, press and hold the MENU button for several seconds. The message "OSD LOCKED" appears. You can unlock the OSD settings at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" appears. - + Buttons - Button ( ) Use these buttons to select or adjust functions in the On Screen Display. For more information, refer to page A16. + Button Use this button to make either D-Sub or DVI connector (SOURCE Hot key) active. This feature is used when two computers are connected to the display. [. . . ] G Do you see a "CHECK SIGNAL CABLE" message on the screen?· This message appears when the signal cable between your PC and the display is not connected. Check the signal cable and try again. Do you see an "OSD LOCKED" message on the screen? G Do you see "OSD LOCKED" when you push MENU button?· You can secure the current control settings, so that they cannot be inadvertently changed. [. . . ]