User manual LG L206WTQS

[. . . ] The power supply cord is used as the main disconnection device. Ensure that the socket-outlet is easily accessible after installation. Operate the display only from a power source indicated in the specifications of this manual or listed on the display. If you are not sure what type of power supply you have in your home, consult with your dealer. [. . . ] Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. A3 Connecting the Display Disassembling the stand 1. Put a cushion or soft cloth on aflat surface. 2. Place the monitor face Down on the cushion or soft cloth. 3. Pushing Latch inside, Take the stand base from stand body. 4. Please pull the stand body lightly to separate it from the hinge body. A4 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5°~15° Swivel : 355° Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. A5 Connecting the Display Using the Computer 1. Make sure to turn off the computer and product. Connect the cable as below sketch map form 1 to 2 . A Connect DVI Cable B Connect Dsub Cable (PC) C Connect Dsub Cable (Mac) Analog signal Digital signal D-sub DVI Power Cord Wall-outlet type PC-outlet type B DVI-D(This feature is not available in all countries. ) A C Mac adapter For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector. 2. Press button on the front switch panel to turn the power on. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making image adjustments. To make adjustments in the On Screen Display, follow these steps: MENU -+ AUTO/SET -+ MENU Press the MENU Button, then the main menu of the OSD appears. To access a control, use the - or + Buttons. When the icon you want becomes highlighted, press the AUTO/SET Button. Use the - /+ Buttons to adjust the image to the desired level. Use the AUTO/SET Button to select other sub-menu items. Push the MENU Button once to return to the main menu to select another function. Push the MENU Button twice to exit from the OSD. A9 On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu PICTURE Sub-menu BRIGHTNESS CONTRAST GAMMA COLOR PRESET RED GREEN BLUE HORIZONTAL POSITION VERTICAL CLOCK SHARPNESS SETUP LANGUAGE OSD HORIZONTAL A D Reference To adjust the brightness, contrast and gamma of the screen To customize the color of the screen sRGB 6500K 9300K To adjust the position of the screen To improve the clarity and stability of the screen TRACKING PHASE POSITION VERTICAL To customize the screen status for a user's operating environment WHITE BALANCE POWER INDICATOR FACTORY RESET FLATRON F-ENGINE MOVIE / TEXT USER NORMAL To select or customize desired image settings : Adjustable A : Analog Input D : Digital Input NOTE The order of icons may differ depending on the model (A10~A14 ). A10 On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears. Menu Name PICTURE Icons Sub-menus Button Tip MENU -+ SET : Exit : Adjust (Decrease/Increase) : Enter : Select another sub-menu NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual. A11 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description PICTURE PICTURE BRIGHTNESS CONTRAST GAMMA To adjust the brightness of the screen. [. . . ] · This message appears when the signal cable between your PC and your display is not connected. Check the signal cable and try again. Do you see a "OSD LOCKED" message on the screen? G Do you see "OSD LOCKED" when you push MENU button?· You can secure the current control settings, so that they cannot be inadvertently changed. You can unlock the OSD controls at any time by pushing the MENU button for several seconds: the message "OSD UNLOCKED" will appear. A15 Troubleshooting Display image is incorrect G Display Position is incorrect. [. . . ]