User manual LG L246WSH

[. . . ] They may result in a shock or fire hazard. Call your service technician for replacement. There are no user serviceable components inside. There are Dangerous High Voltages inside, even when the power is OFF. [. . . ] Insert the hooks into slots. Stand Base Slot Stand Body Hook Warning The tape and locking pin may only be removed from those monitors equipped with a standing base when the base is pulled up. Otherwise, you may be injured by the protruding sections of the stand. A3 Connecting the Display 4. Attach the monitor to the Stand Base by turning the screw to the right. Screw : Turn the screw by using the screw handle. 5. Lift and turn the monitor to face towards the front after the connection is made to the female part of the cable you're attaching. 6. Take the screw out by turning to the left to separate the monitor and Stand Base. Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. A4 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5°~20° Swivel :350° Height Range : maximum 3. 94 inch (100. 0mm) 100. 0mm * Please be sure to remove the Locking pin to adjust the height. Notice You do not need to replace the Locking pin after it is removed, to adjust its height. Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. Slightly wipe stained spot on the exterior only with the cleansing cloths for the product exterior if there is stain or fingerprint on surface of the exterior. Do not wipe roughly when removing stain. Please be cautious of that excessive power may cause scratch or discoloration. A5 Connecting to External Devices When Connecting to your PC 1. Place the monitor in a convenient, well-ventilated location near your computer. When attached, tighten the thumbscrews to secure the 3. Connect the power cord into a proper power outlet that is easily accessible and close to the display. 2 NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. To adjust height of your monitor, unlock the stand lock on top of the stand. 1 D-SUB Power Cord 2 1 Signal Cable Varies according to model. Wall-outlet type PC MAC Mac adapter For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector. 4. Press button on the front switch panel to turn the power on. When monitor power is turned on, the 'Self Image Setting Function' is executed automatically. NOTE ` Self Image Setting Function'?This function provides the user with optimal display settings. When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals. When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted screen while using the device or after changing screen resolution, press the AUTO function button to improve resolution. A6 Connecting to External Devices To arrange the cables Connect the power cord and the signal cable as shown in the figure and then fix them to the cable holders 1 and 2. 1. Please insert the cable holder1 into a hole. 2. Please put the power cord and the signal cable in the cable holder 1. D-SUB D-SUB Cable Holder 1 3. Please put the power cord and the signal cable in the cable holder 2. While pressing the bottom of cable holder 2 with one hand, pull the top of it with the other hand as shown in the picture. Pull Press D-SUB Cable Holder 2 A7 Control Panel Functions Front Panel Controls AUTO Button For optimal display change resolution to 1920x1200 AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the AUTO button before entering the On Screen Display(OSD). [. . . ] · Set the color setting higher than 24 bits (true color) at Control Panel - Settings. The screen blinks. · Check if the screen is set to interlace mode and if yes, change it to the recommend resolution. Have you installed the display driver? Have you installed the display driver?· Be sure to install the display driver from the display driver CD (or diskette) that comes with your display. Or, you can also download the driver from our web site: http://www. lge. com. · Make sure to check if the video card supports Plug&Play function. Do you see an "Unrecognized monitor, Plug&Play (VESA DDC) monitor found" message? A17 Specifications Display 24 inches (61. 3 cm) Flat Panel Active matrix-TFT LCD Anti-glare coating 24 inches viewable 0. 270 mm pixel pitch Horizontal Freq. [. . . ]