User manual LG L3200T

[. . . ] These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. • A suitable conduit entries, knock-outs or glands shall be provided in the cable entries of this product in the end user. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] 2 3 4 DC type lenses Damping Damping + Drive + Drive - 16 Connections Rewire the lens iris plug 1. Cut off the plug of the lens cable, cut off approximately 8 mm of the insulation, and then strip approximately 2 mm of the ends of the cable sheaths. 2. Solder the ends of the cable wires to the ends of the pins, and then attach the cover of the lens iris plug. 17 Connections Flange-back Adjustment The adjustment is required only when a lens without focus-adjusting mechanism is mounted, or when a lens with adjusting mechanism is mounted and focus that is more accurate is needed. Up and down the flange-back adjusting lever to obtain a focused point while watching the monitor screen. The setup menu screen appears on the monitor. • RETURN: Return to the previous. Setting the USER TITLE You can use the camera identification to assign a number and character to the camera. The USER TITLE is displayed on the upper left of the screen. To disappear the user title, select [OFF]. Use [LEFT] or [RIGHT] button to select a [ON] then press [SET]. The USER TITLE menu appears. 2. Use [UP] or [DOWN] button to select an option then press [SET] button. Use [UP] or [DOWN] button to select a submenu option. If you set the brightness to higher value, the image gets bright. • 1. 2. Select [BRIGHTNESS] option. Use [LEFT] or [RIGHT] button to set the bright level. • 27 Menu Operation AGC (Automatic Gain Control) setting If the images are too dark, change the maximum [AGC] value to make the images brighter. SHUTTER (Shutter Speed) setting Select the desired shutter speed for camera exposure. You can change the shutter speed to higher speed to capture fast-moving subjects, though the image becomes darker. 1. 2. Select [AGC] option. Use [LEFT] or [RIGHT] button to select a mode. 1. 2. Select [SHUTTER] option. Use [LEFT] or [RIGHT] button to set shutter speed. Note: If you set the shutter speed value in ALC2 mode, it is maximum value. When the camera is activated with ALC2 mode, the shutter speed is arrived maximum value and then the camera is change to iris control mode automatically for the camera exposure. 28 Menu Operation SENS-UP setting If pictures are not clear due to darkness, this SENS-UP operation would increase the sensitivity of picture. Note: If you set to one of the SHUTTER options except AUTO on the [SHUTTER] menu the [SENS-UP] setting is not available and [---] mark is displayed. White Balance settings Select the method by which the camera shifts its output colors to compensate for the color of a light source. 1. 2. Use [UP] or [DOWN] button to select [SENS-UP] option. Use [LEFT] or [RIGHT] button to select mode. • AUTO: Adjust the sensitivity of the picture automatically. >> • SENS-UP LIMIT: Use [LEFT] or [RIGHT] button to set the SENS-UP limit. OFF: Not used. 1. 2. Select [WHITE BAL] option. [. . . ] Use [LEFT] or [RIGHT] button to select a digital effect. • • • • V-FLIP: Flip the picture vertically. (180°) MIRROR: Turn on the mirror effect. OFF: Turn off the digital effect. 36 Menu Operation Motion Detection Setting The motion detection detects the moving objects in the scene by monitoring changes in brightness level. [. . . ]