User manual LG LB-H2460CL

[. . . ] OPERATION DESCRIPTION 7-1 7-2 7-3 7-4 7-5 7-6 Outline of Air Conditioner Control Description of Operation Circuit Hi POWER Mode High-Temperature Limit Control Low-Temperature Limit Control Auto Restart Function 7-7 Filter Check Lamp 8. INSTALLATION PROCEDURE 8-1 8-2 8-3 8-4 8-5 8-6 8-7 9-1 9-2 9-3 9-4 9-5 9-6 Safety Cautions Installation Diagram of Indoor and Outdoor Units Installation Indoor Unit Outdoor Unit How to Set Remote Control Selector Switch Others Troubleshooting Procedure Basic Check Items Primary Judgement Self-Diagnosis by Remote Control (Check Code) Troubleshooting Flowcharts Troubleshooting for Remote Control (Including The Indoor P. C. TROUBLESHOOTING CHART ­1­ FILE NO. PARTS REPLACEMENT 10-1 10-2 10-3 10-4 11-1 11-2 11-3 11-4 11-5 Indoor Unit Outdoor Unit (RAS-13UA-ES) Outdoor Unit (RAS-10UA-ES) Outdoor Unit (RAS-07UA-ES) Indoor Unit (E-Parts Assy) Indoor Unit Outdoor Unit (RAS-13UA-ES) Outdoor Unit (RAS-10UA-ES) Outdoor Unit (RAS-07UA-ES) 11. [. . . ] When the outdoor unit is installed in a place exposed always exposed to strong wind like a coast or on a high storey of a building, secure the normal fan operation using a duct or a wind shield. In particularly windy areas, install the unit such as to avoid admission of wind. Installation in the following places may result in trouble. · A saline-place such as the coast. · A place where high-frequency waves are likely to be generated as from audio equipment, welders, and medical equipment. Drain hose Inside the room Extension drain hose Fig. 8-4-23 CAUTION Arrange the drain pipe for proper drainage from the unit. Improper drainage can result in dew-dropping. This air conditioner has the structure designed to drain water collected from dew, which forms on the back of the indoor unit, to the drain pan. Therefore, do not store the power cord and other parts at a height above the drain guide. Wall Drain guide Strong wind Space for pipes Fig. Cut the pipe with a pipe cutter. Obliquity Roughness Warp (Unit : N·m) Outer dia. of copper pipe 6. 35 mm 9. 52 mm Tightening torque 16 to 18 (1. 6 to 1. 8 kgf·m) 33 to 42 (3. 3 to 4. 2 kgf·m) 90° Fig. Perform evacuating for about 15 minutes if the piping length is 20 meters. (15 minutes for 20 meters) (assuming a pump capacity of 27 liters per minute. ) Then confirm that the compound pressure gauge reading is ­101 kPa (­76 cmHg). Close the low pressure side valve handle of gauge manifold. Open fully the valve stem of the packed valves (both sides of Gas and Liquid). Remove the charging hose from the service port. Securely tighten the caps on the packed valves. Compound pressure gauge -101kPa (-76cmHg) Manifold valve Handle Lo Charge hose (For R-410A only) Connecting pipe Handle Hi (Keep full closed) Charge hose (For R-410A only) Pressure gauge <Packed valve handling precautions> · Open the valve stem all the way out; but do not try to open it beyond the stopper. · Securely tighten the valve stem cap with torque in the following table: Gas side (9. 52 mm. ) Liquid side (6. 35 mm. ) Service port 33 to 42 N·m (3. 3 to 4. 2 kgf·m) 16 to 18 N·m (1. 6 to 1. 8 kgf·m) 9 to 10 N·m (0. 9 to 1. 0 kgf·m) Hexagonal wrench is required. 4m m Fig. 8-5-8 Vacuum pump adapter for counter-flow prevention (For R-410A only) Vacuum pump Packed valve at gas side Service port (Valve core (Setting pin)) Packed valve at liquid side Fig. How to Set Remote Control Selector Switch 1. Remove the electric parts cover from the outdoor unit. 2. Connect the connecting cable to the terminal as identified with their respective matched numbers on the terminal block of indoor and outdoor unit. [. . . ] 2) Remove the fixing screw and the capacitor band. (1-Screw 4 x 10L) 3) Disconnect the lead wires. For compressor For fan motor 3 Capacitor for fan motor ­ 57 ­ FILE NO. 1 Part name Common procedure Procedures 1) Stop the operation of air-conditioner, and disconnect the power cord from the AC supply. (2-Screws 4 x 10L) 3) Remove the cord clamp (2-Screws 4 x 22L) and disconnect the connecting cable. [. . . ]