User manual LG LBNM9080BL-LBUM9080BL

[. . . ] The power supply cord is used as the main disconnection device. Ensure that the socket-outlet is easily accessible after installation. Operate the display only from a power source indicated in the specifications of this manual or listed on the display. If you are not sure what type of power supply you have in your home, consult with your dealer. [. . . ] Assemble the Stand Base(Front, Rear) into the Stand Body in the correct direction. Stand Base 4. Use a coin on the back of the stand base and turn the screw clockwise to tighten. 5. Once assembled take the monitor up carefully and face the front side. Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. 5 Connecting the Display Disassembling the stand 1. Put a cushion or soft cloth on aflat surface. 2. Place the monitor face Down on the cushion or soft cloth. 3. Remove the Stand Body and Stand Base from product in correct direction as shown in the picture. 4. Use a coin on the back of the Stand Base and turn the screw anticlockwise to loosen. 6 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display -After installation, adjust the angle as shown below. 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5° to 15° Do not touch or press the screen when adjusting the angle of the monitor. When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body. (Only Analog Mode) This will automatically adjust your display image to the ideal settings for the current screen resolution size (display mode). The best display mode is E1941T/E1941S : 1366 x 768 E2041T/E2041S : 1600 x 900 E2241T/E2241S/E2341T/E2441T/E2541T: 1920 x 1080 INPUT Button (SOURCE Hot key) When two input signals are connected, you can select the input signal (D-SUB/DVI) you want. When only one signal is connected, it is automatically detected. (Only E1941T/E2041T/E2241T/E2341T/E2441T/E2541T ) EXIT Button Exit the OSD(On Screen Display). Power Button & Use this button to turn the display on or off. Power Indicator The power indicator stays blue if the display is running properly (On Mode). If the display is in Sleep Mode , the power indicator is blinking blue. 11 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. To make adjustments in the On Screen Display, follow these steps: 1 2 3 4 Press the discretionary Button, then the main menu of the OSD appears. To access a control, use the corresponding Buttons. Use the Use the // Buttons to adjust the image to the desired level. When current setting value is ON, the SUPER SAVING color is green. OFF Turn off the SUPER ENERGY SAVING function. Now the monitor is LED SAVING function. [. . . ] 15 pin D-Sub Connector RGB Analog (0. 7 Vp-p/ 75 ohm) VESA 1600 x 900 @ 60 Hz VESA 1600 x 900 @ 60 Hz E2041S Sync Input Video Input Resolution Plug&Play Power Consumption Dimensions & Weight With Stand Width 47. 6 cm ( 18. 74 inch ) Height 36. 4 cm ( 14. 33 inch ) Depth 16. 6 cm ( 6. 54 inch ) Weight(excl. packing) Without Stand Width 47. 6 cm ( 18. 74 inch ) Height 30. 3 cm ( 11. 92 inch ) Depth 5. 7 cm ( 2. 24 inch ) 2. 7 kg ( 5. 95 lb ) Range Power Input Environment al Conditions Tilt : -5° to 15° AC 100-240 V~ 50 / 60 Hz 1. 0 A Operating Conditions Temperature 10 °C to 35 °C Humidity 10 % to 80 % non-Condensing Storage Conditions Temperature -20 °C to 60 °C Humidity 5 % to 90 % non-Condensing Stand Base Power cord Attached ( ), Detached ( O ) Wall-outlet type NOTE Information in this document is subject to change without notice. 25 Specifications Display 54. 6 cm (21. 5 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 54. 6 cm 0. 248 mm x 0. 248 mm (Pixel pitch) Horizontal Freq. Input Form 30 kHz to 83 kHz (Automatic) 56 Hz to 75 Hz (Automatic) Separate Sync. Digital E2241T Sync Input Video Input Signal Input Input Form 15 pin D-Sub Connector DVI-D Connector (Digital) RGB Analog (0. 7 Vp-p/ 75 ohm), Digital VESA 1920 x 1080 @ 60 Hz VESA 1920 x 1080 @ 60 Hz Resolution Plug&Play Power Consumption Dimensions & Weight Max Recommend DDC 2B(Analog, Digital) On Mode Sleep Mode Off Mode : < < 24 W(Typ. ) 0. 3 W 0. 3 W Without Stand Width 50. 9 cm ( 19. 80 inch ) Height 32. 2 cm ( 12. 67 inch ) Depth 5. 8 cm ( 2. 28 inch ) 2. 9 kg (6. 39 lb) With Stand Width 50. 9 cm ( 19. 80 inch ) Height 38. 8 cm ( 15. 27 inch ) Depth 16. 6 cm ( 6. 54 inch ) Weight(excl. [. . . ]