User manual LG LK-0580AC

[. . . ] 6 1-3 Basic system component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1-3-1 Apparatus component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1-3-2 The control system devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 1-3-3 The control system devices (Procured on site) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Automatic address: Setup from SW15 on the interface P. C. board of the header unit It requires a maximum of 10 minutes (Usually, approx. 5 minutes) to set up automatically an address to 1 refrigerant line. To set up an address automatically, setup at the outdoor unit is necessary. (Address setup cannot be performed by power-ON only. ) 62 4-3-1 (1) Check at main power-ON After turning on the main power of the indoor units and outdoor units in the refrigerant system. Prior to starting test operation, check the following items in each outdoor and indoor unit. (After turning on the main power, be sure to check in order of indoor unit outdoor unit. ) Check on outdoor unit 1. Check that all the rotary switches, SW01, SW02 and SW03 on the interface P. C. board of the header outdoor unit are set to "1". If an error code is displayed on 7-segment [B], remove the cause of the fault . Check that [L08] is displayed on the 7-segment display [B] on the interface P. C. (OK when display goes on. ) Group address (Group address) Individual : 0000 Header unit : 0001 Follower unit : 0002 8 9 10 11 In case of group control Using the code. buttons, set on the item Operation procedure Using the buttons, set Individual = , Header unit = , Follower unit = Push the button. (OK when display goes on. ) Push the button. (Status returns to the normal stop status. ) . 1 7 2 8 3 9 456 10 11 End Data Item code 2, 5, 8 11 1 4, 7, 10 3, 6, 9 65 4-3-1 (3) Line (System) address setting 1. board of the header unit in each system, set up the system address for each system. (At shipment from factory: Set to Address 1) Note) Be careful not to duplicate with other refrigerant line. Header unit interface P. C. board ON ON ON ON 1234 1234 1234 1234 SW11 SW12 SW13 SW14 ON ON 1234 1234 ON ON ON 1 1234 1234 SW06 SW07 SW08 SW09 SW10 System address switch on outdoor interface P. C. board System address 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1 SW13 2 3 4 1 SW14 2 3 4 ( : Switch ON, × : Switch OFF) SW13 2 3 4 1 SW14 2 3 4 × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × System address 15 16 17 18 19 20 21 22 23 24 25 26 27 28 1 × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × × : Is not used for setup of system address. Check that the relay connectors between [U1U2] and [U3U4] terminals are connected to all the header units to which the central control is connected. (At shipment from factory: No connection of connector) CAUTION Be sure to allocate different line addresses for each refrigerant system even if there are two or more TCS-NET relay interfaces. 4-3-1 (4) Power reset · To activate the line address on both the outdoor and indoor unit side, power supply is temporarily reset. · When power returns, be sure to power up the indoor units prior to the outdoor unit. 66 4-3-1 (5) Indoor unit address check Step Item 1 Power - on Operation and check contents Initial communication takes a couple of minutes. During initial communication, 7-segment display section is as follows. [. . . ] Remove the cause and then power on the air conditioner, Intelligent Server and Relay Interface. Remove the cause and then power on the Energy Monitoring Relay Interface and Intelligent Server. Remove the cause and then power on the Digital I/O Relay Interface and Intelligent Server. 101 Other faults No. Description Possible causes Remedy 1 Nothing is displayed on the Touch Screen Controller screen. Touch Screen Controller is not powered on. [. . . ]