User manual LG LMF9060TS

[. . . ] Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. REGULATORY INFORMATION: FCC Part 15 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. [. . . ] The frame rate is the number of recorded frames per second. According to resolution, the frame rate is set automatically. · · · · · In: Displays the number of the ALARM-IN terminal. Sensor Type: The sensor state can be set to either N. O. Camera: Select the connected camera channel to the ALARM-IN terminal. Relay Output: Select the alarm (relay) output number for the RELAY-OUT terminal for the output alarm (relay) signal. When the input is activated, the camera moves to the selected preset position and the picture of the camera in that position appears on the monitor. NOTE · · If the video of some IP cameras is not displayed, you should set the [Resolution] option to CIF (352x240 or 352x288). If you want to set the Frame Rate manually for each recoding setting menu, refer to the below. LE5016/LE5008 Series Resolution 352*240 NTSC 704*240 704*480 352*288 PAL 704*288 704*576 LE4016/LE4008 Series Resolution 352*240 NTSC 704*240 704*480 352*288 PAL 704*288 704*576 Frame Rate 1, 3, 5, 7. 5, 10, 15, 30 1, 3, 5, 7. 5, 10, 15 1, 3, 5, 7. 5 1, 3, 5, 6, 7. 5, 12. 5, 25 1, 3, 5, 6, 7. 5, 12. 5 1, 3, 6 1, 3, 5, 6, 7. 5, 12. 5, 25 1, 3, 5, 7. 5, 10, 15, 30 Frame Rate Motion · · · · Channel: Select the channel to set motion detection. Sensitivity: Set the level of sensitivity for the created motion detection area. Sensitivity can be set from level 01 to 10 or OFF. Relay Output: 01 to 04: Outputs the alarm (relay) signal via the RELAY-OUT terminal. When the DVR detects text input, it triggers output signals on all the associated RELAY-OUT connectors. NONE: Not used. Spot Monitor: Select the event type for the spot monitor display when the event is activated. Notification Marks up when you want to activate the selected option. If the selected notification option is activated, the device will notify the user about the information of selected option by E-mail. · · · · · - 40 Installation · · · · · Sensor On: Sends an e-mail when a sensor has occurred. Motion Detection: Sends an e-mail when a motion detection has occurred. Text In: Sends an e-mail when a text input is detected. Admin Password Changed: Sends an e-mail when the administrator password has changed. Video Loss: Sends an e-mail when a video signal from the camera has stopped because of a cable disconnection or malfunction of a camera. Power On/Off: Sends an e-mail when power is on or off. Disk Full: Sends an e-mail when the HDD has fully recorded. Emergency · · 3 Installation Mail · · Notification: Marks up to notify the emergency agent about unit operating information according to your notification settings. Host Name/Port: Enter the Host Name and port number of the emergency agent program. [. . . ] Check the type of sensor in the camera setting is the same as with the connected sensor. The connected sensor is not operating. Check the system is set to use the sensor in the recording schedule window in the recording setting menu. Check the sensor is properly connected to the ALARM-IN. Check the system is set to use the PTZ camera in the camera setting menu. Check the power cable of the PTZ camera is properly connected. 6 Troubleshooting The connected PTZ camera is not operating. Check the signal cable of the PTZ camera is properly connected. [. . . ]