Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual LG LMV1650ST. We hope that this LG LMV1650ST user guide will be useful to you.
Lastmanuals help download the user guide LG LMV1650ST.
Detailed instructions for use are in the User's Guide.
[. . . ] See Figure 2.
BE SURE TO READ THE FOLLOWING SAFETY INSTRUCTIONS:
Model Number Plate Mounting Plate
Model Number Plate
Mounting Plate
Figure 1
Figure 2
WARNING
For Your Safety
· You will need TWO people to install this oven. It is heavy and could cause personal injury if not handled
properly.
· Avoid Electrical Shock!
Before you drill into the wall, note where electrical outlets are and where electrical wires might be behind concealed in the wall, YOU COULD RECEIVE AN ELECTRICAL SHOCK if you contact electrical wires with your drill bit. Locate and disconnect the power of any electrical circuits that could be affected by installing this oven. IF YOU DO NOT DISCONNECT THE POWER, YOU RECEIVE AN ELECTRICAL SHOCK.
· ELECTRICAL RATING OF THIS OVEN : 120V AC. [. . . ] Examples For 3 1/4"x10" SYSTEMS
6ft. wall cap transition 2ft.
For 6"ROUND SYSTEMS
6ft. wall cap
2ft.
1-3 1/4" x 10" 90° elbow 1-Wall Cap 8 feet straight duct TOTAL LENGTH
= = = =
25 ft. 73 ft.
1-transition 2-90° elbows 1-Wall Cap 8 feet straight TOTAL LENGTH
= = = = =
5 ft. 73 ft.
9
STEP 3: PREPARE THE VENTING BLOWER
WARNING
G
To avoid risk of property damage, unplug the microwave oven or disconnect power at source by removing fuse or throwing circuit breaker. To avoid risk of personal injury, wear protective gloves when handling mounting plate.
G
DO NOT PULL OR STRETCH THE BLOWER WIRING!Pulling and stretching the blower wiring could result in electrical shock.
G
Your microwave oven is shipped with the blower assembled for room venting. If you want wall-venting or roof-vented installation, you must change the blower, as detailed below.
A thick, protective covering
Before You Start
1. Remove any shipping materials and parts from inside the microwave oven. Cover the counter top or cooktop with a thick, protective covering to protect it from damage and dirt. NOTE: If you have a free-standing range, disconnect it, move it onto a piece of cardboard or hardboard and pull it away from the wall, so that you can get closer to the upper cabinet and back wall for easier measuring and drilling.
Figure 11
Mounting plate Mounting plate screw(s) (1 or 2 screws) Control Panel Side
Remove The Mounting Plate:
1. See Figure 22.
parts "B" blower unit
blower plate mounting screw (option)
blower plate
blower unit back plate
blower unit exhaust ports
blower unit mounting screw (option)
Figure 18
blower plate mounting screw (option) blower plate back plate
blower unit mounting screw (option)
8. Attach the exhaust adapter to the blower plate by sliding it into the Guide. Locate and disconnect power to any electrical circuits that could be affected by installing this oven.
WARNING
To avoid risk of personal injury, electrical shock or death, cover the edge of the power supply cord hole with the power supply cord bushing.
Drill The Holes In The Wall And Upper Cabinet.
cabinet front filler block
1. If there is a stud, drill a 3/16" hole for lag screws. If there is no stud, drill a 3/4" hole for toggle screws. Make sure to use at least 1 lag screw in a stud, and 4 toggle screws in the drywall or the plaster. Drill a 3/8" hole at points J and K on the upper cabinet template. NOTE: If the bottom of the upper cabinet is recessed 3/4" or more, you will need 2"x 2" filler blocks (not included) to provide additional support for the bolts. Mark the center of each filler block and drill a 3/8" diameter hole at the marks. Align filler blocks over the two openings in the top of the microwave oven cabinet and attach to cabinet with masking tape. Cut or drill a 2" diameter hole at the area marked M. [. . . ] Remove the mounting plate and draw lines extending through the points. This will give the location and size of the box cutout for the rear wall duct. (Figure 30) 3 pieces mounting plate: Use the wall template to determine the location and size of the box cutout for the rear wall duct. Attach the exhaust adapter to the rear mounting plate (back plate) wall side. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE LG LMV1650ST
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual LG LMV1650ST will begin.