User manual LG LMV1650SW

[. . . ] See Figure 2. BE SURE TO READ THE FOLLOWING SAFETY INSTRUCTIONS: Model Number Plate Mounting Plate Model Number Plate Mounting Plate Figure 1 Figure 2 WARNING For Your Safety · You will need TWO people to install this oven. It is heavy and could cause personal injury if not handled properly. · Avoid Electrical Shock! ­ Before you drill into the wall, note where electrical outlets are and where electrical wires might be behind concealed in the wall, YOU COULD RECEIVE AN ELECTRICAL SHOCK if you contact electrical wires with your drill bit. ­ Locate and disconnect the power of any electrical circuits that could be affected by installing this oven. IF YOU DO NOT DISCONNECT THE POWER, YOU RECEIVE AN ELECTRICAL SHOCK. · ELECTRICAL RATING OF THIS OVEN : 120V AC. [. . . ] Examples For 3 1/4"x10" SYSTEMS 6ft. wall cap transition 2ft. For 6"ROUND SYSTEMS 6ft. wall cap 2ft. 1-3 1/4" x 10" 90° elbow 1-Wall Cap 8 feet straight duct TOTAL LENGTH = = = = 25 ft. 73 ft. 1-transition 2-90° elbows 1-Wall Cap 8 feet straight TOTAL LENGTH = = = = = 5 ft. 73 ft. ­9­ STEP 3: PREPARE THE VENTING BLOWER WARNING G To avoid risk of property damage, unplug the microwave oven or disconnect power at source by removing fuse or throwing circuit breaker. To avoid risk of personal injury, wear protective gloves when handling mounting plate. G DO NOT PULL OR STRETCH THE BLOWER WIRING!Pulling and stretching the blower wiring could result in electrical shock. G Your microwave oven is shipped with the blower assembled for room venting. If you want wall-venting or roof-vented installation, you must change the blower, as detailed below. A thick, protective covering Before You Start 1. Remove any shipping materials and parts from inside the microwave oven. Cover the counter top or cooktop with a thick, protective covering to protect it from damage and dirt. NOTE: If you have a free-standing range, disconnect it, move it onto a piece of cardboard or hardboard and pull it away from the wall, so that you can get closer to the upper cabinet and back wall for easier measuring and drilling. Figure 11 Mounting plate Mounting plate screw(s) (1 or 2 screws) Control Panel Side Remove The Mounting Plate: 1. See Figure 22. parts "B" blower unit blower plate mounting screw (option) blower plate blower unit back plate blower unit exhaust ports blower unit mounting screw (option) Figure 18 blower plate mounting screw (option) blower plate back plate blower unit mounting screw (option) 8. Attach the exhaust adapter to the blower plate by sliding it into the Guide. Locate and disconnect power to any electrical circuits that could be affected by installing this oven. WARNING To avoid risk of personal injury, electrical shock or death, cover the edge of the power supply cord hole with the power supply cord bushing. Drill The Holes In The Wall And Upper Cabinet. cabinet front filler block 1. If there is a stud, drill a 3/16" hole for lag screws. If there is no stud, drill a 3/4" hole for toggle screws. Make sure to use at least 1 lag screw in a stud, and 4 toggle screws in the drywall or the plaster. Drill a 3/8" hole at points J and K on the upper cabinet template. NOTE: If the bottom of the upper cabinet is recessed 3/4" or more, you will need 2"x 2" filler blocks (not included) to provide additional support for the bolts. Mark the center of each filler block and drill a 3/8" diameter hole at the marks. Align filler blocks over the two openings in the top of the microwave oven cabinet and attach to cabinet with masking tape. Cut or drill a 2" diameter hole at the area marked M. [. . . ] Remove the mounting plate and draw lines extending through the points. This will give the location and size of the box cutout for the rear wall duct. (Figure 30) ­ 3 pieces mounting plate: Use the wall template to determine the location and size of the box cutout for the rear wall duct. Attach the exhaust adapter to the rear mounting plate (back plate) wall side. [. . . ]