User manual LG LMV1680BB

[. . . ] CONSTRUCTION VIEWS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPECIFICATIONS OF ELECTRICAL PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . REFRIGERANT CYCLE DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Do not form the drain hose into the waved shape. 50 mm or more Fig. 10-3-18 · Carefully arrange the pipes so that none of the pipes stick out of the rear plate of the indoor unit. · Carefully connect the auxiliary pipes and connecting pipes to each other and cut off the insulating tape wound on the connecting pipe to avoid double-taping at the joint, moreover, seal the joint with the vinyl tape, etc. · Since condensation can result in machine performance trouble, be sure to insulate both connecting pipes. (Use polyethylene foam as insulating material. ) · When bending a pipe, be careful not to crush it. Do not put the drain hose end into water. Do not put the drain hose end in the drainage ditch. Fig. Put water in the drain pan and make sure that the water is being drained outside. When connecting extension drain hose, insulate the connection part of extension drain hose with shield pipe. Shield pipe 10-3-6. Pass the pipe through the hole in the wall, and hook the indoor unit on the installation plate at the upper hooks. Swing the indoor unit to right and left to confirm that it is firmly hooked on the installation plate. While pressing the indoor unit onto the wall, hook it at the lower part on the installation plate. Pull the indoor unit toward you to confirm that it is firmly hooked on the installation plate. 1 Drain hose Inside the room Extension drain hose Fig. When the outdoor unit is to be mounted high on a wall, take particular care to ensure that parts do not fall, and that the installer is protected. When doing installation work at ground level, it is usual to make wiring and pipe connections to the indoor units, first, and then to make connections to the outdoor unit. However, if outdoor work is difficult it is possible, instead, to make changes to the procedure. For example, by making adjustments to the wiring and piping lengths on the inside (rather than the outside). A place where the drain water does not cause any problems. 80 mm or more only when unobstructed to the front and both sides In principle, leave open (D) 50 mm or more from wall 100 mm or more from wall (C) 250 mm or more from wall (A) As shown in the figure, position power cord and connecting cable downward, and lead out along piping connection port. (B) 200 mm or more Power cord Extension drain hose When installing the outdoor unit, leave open in at least two of directions (A), (B), (C) and (D) shown in the right figure. Ensure sufficient space to allow drainage C 10 m or less Outdoor unitl Fig. 10-5-1 Installation diagram of outdoor units ­ 56 ­ 10-5-2. Fixing Bolt Arrangement of Outdoor Unit 10-5-3. Refrigerant Piping Connection Flaring 1. Cut the pipe with a pipe cutter. 600 mm Suction side 90° Obliquity Roughness Warp 310 mm Fig. Insert a flare nut into the pipe, and flare the pipe. [. . . ] Otherwise it would cause insulation inferiority because of dew drops. 3) When replacing the sensor using the colored protective tube, wind the color tape matching the color of that tube. These are parts for servicing sensors. Please check that the accessories shown in the right table are packed. Parts name 1 2 3 4 5 6 Sensor Sensor Spring (A) Sensor Spring (B) Thermal constringent tube Color tape Terminal Q'ty 1 1 1 3 1 3 Remarks Length : 3m For spare For spare Including one spare 9 colors ­ 98 ­ <MCC-1438> ­ 99 ­ <MCC-818> ­ 100 ­ 13. Indoor Unit (1) 240 238 247 235 236 201 203 221, 222, 224 246 227 205 202 245 204 232 233 228 206 229 239 223 210 218, 219 207 215 211 216 213 225, 226 212 230 214 234 217 209 The parts in the following parts list are conformed to RoHS. [. . . ]