User manual LG LPC12

[. . . ] The user could lose the authority to operate this equipment if an unauthorized change or modification is made. REGULATORY INFORMATION: FCC Part 15 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. [. . . ] (Set the Duration Time of Alarm Input function to "1 to 255". ) <Example : If this unit receives signal from "Alarm 8"> · Manual mode: Change the observe position to a sensor that senses a touch or shock then keep observe the sensed position. (Set the Duration Time of Alarm Input function to "0". ) Note : The Alam In 1 is Preset 1, Alam In 2 is Preset 2, Alam In 3 is Preset 3, . . . , Alam In 7 is Preset 7 and Alam In 8 is Preset 8. <Example : If this unit receives signal from "Alarm 8"> 14 LPC12_ATURALI_ENG. qxp:LPT-EP553PS_ATURALI_ENG 2008. 4. 29 5:38 PM Page 15 Alarm Input function Listed below are the camera actions of alarm input function by different function status in each mode Function status While observe a specific position. Manual mode Change the observe position to the alarmed position then keep observe the alarmed position. Stop preset touring and change the observe position to the alarmed position then keep observe the alarmed position. Stop auto panning and change the observe position to the alarmed position then keep observe the alarmed position. Stop operating pattern function and change the observe position to the alarmed position then keep observe the alarmed position. Auto mode Change the observe position to the alarmed position then return to the position that previously observed. Stop preset touring and change the observe position to the alarmed position then restart the preset touring again. Stop auto panning and change the observe position to the alarmed position then restart the auto panning again. Stop operating pattern function and change the observe position to the alarmed position then restart the pattern function again. While operating Auto Pan function. While operating Pattern function. ALARM OUT Connections Connect an external device, for example, a buzzer or lamp, to this connector. Output specifications are lowactive, open-collector and a drive capacity of 30V DC 0. 5A maximum. · If you want to activate the full-time auto focus mode while a Pan/Tilt operation, set the focus mode to AUTO. FOCUS FOCUS MODE FOCUS DIST ZOOM START ZOOM END ZOOM SPEED ZTRK MODE INITIAL SET RETURN PUSH AUTO 50CM x1 x324 QUICK AUTO ON Focus Settings To avoid AF error or out of Focus, initialization of LENS system by using the "Remote Reset" command of Controller is highly recommended. General Operation 1. Move the cursor to [FOCUS SET] on the [MENU] screen 2. Press the right key and the FOCUS setting menu appears. FOCUS FOCUS MODE FOCUS DIST ZOOM START ZOOM END ZOOM SPEED ZTRK MODE INITIAL SET RETURN PUSH AUTO 50CM x1 x324 QUICK AUTO ON Focus Distance setting Selects the minimum shooting distance for the focus. Select [FOCUS DIST] option on the [FOCUS] menu, then select a Focus Distance value. (1CM, 10CM, 50CM, 1M, 3M, 5M) FOCUS FOCUS MODE FOCUS DIST ZOOM START ZOOM END ZOOM SPEED ZTRK MODE INITIAL SET RETURN PUSH AUTO 50CM x1 x324 QUICK AUTO ON 3. To reset the [FOCUS] settings to factory setting, use [INITIAL SET] option on the [FOCUS] menu. To return to the previous menu, use [RETURN] option on the [FOCUS] menu. 21 LPC12_ATURALI_ENG. qxp:LPT-EP553PS_ATURALI_ENG 2008. 4. 29 5:38 PM Page 22 Zoom Start setting Selects a zoom start position. Select [ZOOM START] option on the [FOCUS] menu, then select a zoom's start position. (x1 - x26) FOCUS Zoom Speed setting Selects a zoom speed. Select [ZOOM SPEED] option on the [FOCUS] menu, then select a zoom speed. (SLOW, MIDDLE, QUICK) FOCUS FOCUS MODE FOCUS DIST ZOOM START ZOOM END ZOOM SPEED ZTRK MODE INITIAL SET RETURN PUSH AUTO 50CM x1 x324 QUICK AUTO ON FOCUS MODE FOCUS DIST ZOOM START ZOOM END ZOOM SPEED ZTRK MODE INITIAL SET RETURN PUSH AUTO 50CM x1 x324 QUICK AUTO ON Zoom End setting Selects a zoom end position. [. . . ] To reset the [F OSD] settings to factory setting, use [INITIAL SET] option on the [F OSD] menu. To return to the previous menu, use [RETURN] option on the [F OSD] menu. 30 LPC12_ATURALI_ENG. qxp:LPT-EP553PS_ATURALI_ENG 2008. 4. 29 5:39 PM Page 31 Privacy Masking Settings Using the LCC-K1000 or controller with Multix protocol for Privacy Zone Setting. This function is aiming at the protection of personal privacy, selecting a screen part black not to be displayed in the screen. Submenus are provided for zone number selection and parameter setting. 5. [. . . ]