User manual LG LRFC25750SB

[. . . ] 5 · PART NAMES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 · USING THE REMOTE CONTROL . . . . . . . . . . . . . . 8 · BASIC OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 · ADJUSTING THE AIR FLOW DIRECTION . . . . . [. . . ] · Condensation may form on the air outlet if the unit operates continuously in the COOL or DRY mode when humidity is over 80 percent. WHEN POWER FAILURE OCCURS This air conditioner has a memory function to store settings when a power failure occurs. After power recovery, the unit will automatically re-start in the same settings which were active before the power failure, except for timer settings. If the timers were set before a power failure, they will need to be re-set after power recovery. TIPS ON SAVING ENERGY Below are some simple ways to save energy when you use your air conditioner. SET THE CORRECT TEMPERATURE · Setting the thermostat 1°C higher than the desired temperature in the COOL mode will save approximately 10 percent in power consumption. · Setting the temperature lower than necessary during cooling operation will result in increased power consumption. BLOCK DIRECT SUNLIGHT AND PREVENT DRAFTS · Blocking direct sunlight during cooling operation will reduce power consumption. · Close the windows and doors during cooling operation. SET PROPER AIR FLOW DIRECTION TO OBTAIN THE BEST AIR CIRCULATION KEEP FILTER CLEAN TO ENSURE THE MOST EFFICIENT OPERATION MAKE MOST OF THE TIMER OFF FUNCTION DISCONNECT THE POWER CORD OR TURN OFF THE CIRCUIT BREAKER WHEN THE UNIT IS NOT USED FOR AN EXTENDED PERIOD OF TIME · The indoor unit still consumes a small amount of power when it is not operating. 5 PART NAMES INDOOR UNIT 1 2 3 4 5 6 7 8 9 0 q w 1 Inlet (Air) 2 Open Panel 3 AUX. Button 4 Air Filters 5 Receiver Window 6 Louvre Unit Open to clean the inside of the air conditioner. 7 Power Supply Cord 8 Indicator Panel 9 Vertical Adjustment Louvres 0 Horizontal Adjustment Louvres q Outlet (Air) w Remote Control e r t y e TURBO COOLING Lamp (green ) r TIMER Lamp (orange t OPERATION Lamp (red ) ) y PLASMACLUSTER Lamp (blue) OUTDOOR UNIT u i o u Inlet(Air) i Refrigerant Tube and Interconnecting Cord o Drainage Hose p Outlet(Air) p NOTE: Actual units might vary slightly from those shown above. 6 REMOTE CONTROL 1 1 TRANSMITTER 2 DISPLAY (Liquid Crystal Display) 3 ON/OFF Button 2 4 TEMP. Button 5 DISPLAY Button 3 4 5 6 7 8 9 0 q w e r t 6 PLASMACLUSTER Button 7 ONE-HOUR OFF TIMER Button 8 MODE Button 9 TIMER ON Button (for setting the timer) 0 FAN Button q TIMER OFF Button (for setting the timer) w SWING Button e TIMER CANCEL Button r TURBO COOLING Button t RESET Button L. C. D. REMOTE CONTROL DISPLAY y MODE SYMBOLS : AUTO : DRY u TURBO COOLING SYMBOL i PLASMACLUSTER SYMBOL o FAN SPEED SYMBOLS : AUTO : Manual setting : COOL y u i o a s p p TEMPERATURE AND TIMER COUNT DOWN INDICATOR a TRANSMITTING SYMBOL s TIMER ON/TIMER OFF INDICATOR Indicates when timer on or timer off is set. 7 USING THE REMOTE CONTROL LOADING BATTERIES Use two size-AAA (R03) batteries. the battery cover 1 Removethe remote control. at the back of compartment, 2 Insert batteries in the± and -- making sure the polarities are correctly aligned. · Lines will be indicated on the display when batteries are properly installed. 3 Reinstall the battery cover. Remote control cover 4 Press the RESET button using a thin stick. NOTES: · The battery life is approximately one year in normal use. Approximately the same numbers of positive and negative ions released into the air will reduce some airborne mold. 1 During operation, press the PLASMACLUSTER button. · The remote control will display " ". · The blue PLASMACLUSTER lamp on the unit will light up. TO CANCEL 1 Press the PLASMACLUSTER button again. · The PLASMACLUSTER lamp on the unit will turn off. NOTES: · Use of the PLASMACLUSTER operation will be memorized, and it will be activated the next time you turn on the air conditioner. · To turn off the PLASMACLUSTER lamp, press the DISPLAY button. · When the PLASMACLUSTER button is pressed while the unit is not operating, the PLASMACLUSTER operation will be performed without accompanying air conditioning mode (eg, COOLING). The mode symbol of the remote control will go off and the fan speed can not be set AUTO. 12 TURBO COOLING OPERATION In this operation, the air conditioner fan works at "extra high" speed with a setting temperature of 15°C to rapidly cool the room. 1 Press the TURBO COOLING button during operation. · The remote control will display " ". · The temperature display will go off. · The green TURBO COOLING lamp ( unit will light up. ) on the TO CANCEL Press the TURBO COOLING button again. · TURBO COOLING operation will also be cancelled when the operation mode is changed, or when the unit is turned off. · The green TURBO COOLING lamp ( ) on the unit will turn off. 1 NOTES: · You cannot set the temperature or fan speed during TURBO COOLING operation. · The fan and temperature settings become "HIGH" speed and 18°C after the unit has run for 30 minutes in TURBO COOLING operation. · To turn off the TURBO COOLING lamp, press the DISPLAY button. ONE-HOUR OFF TIMER When the ONE-HOUR OFF TIMER is set, the unit will automatically turn off after one hour. 1 Press the ONE-HOUR OFF TIMER button. · The remote control will display " ". [. . . ] 6 Make louvrethe allislamps on the indicator panel are notequipment will work and the If the unit not reinstalled properly, the safety lamps will blink, preventing the unit from operating. In such case, reinstall the louvre unit properly. Push the ON/OFF button of the remote control and check if the unit operates properly. 16 MAINTENANCE Be sure to disconnect the power cord from the wall outlet or turn off the circuit breaker before performing any maintenance. CLEANING THE FILTERS The air filters should be cleaned every two weeks. 1 TURN OFF THE UNIT 2 REMOVE THE FILTERS 1 2 3 1 Lift the open panel. 2 Push the air filters up slightly to unlock them. [. . . ]