User manual LG LRFC25750WW

[. . . ] Keep children away from the unit. 5 ALWAYS ensure that the power cable is in good condition. If the power cord is damaged in any way, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard. 6 Do NOT attempt to repair the unit yourself. If it is damaged in any way, contact: x An authorized service center x The dealer from whom you purchased the air conditioner. 7 Do NOT place any brocking objects in front of the unit. 8 If the remote control will not be used for a long time, remove the batteries. [. . . ] Possible temperatures are between 18°C and 30°C inclusive. Hr. C TEMP. Result: x Each time you press the temperature buttons: ­ The temperature is adjusted by 1°C and displayed on the control panel ­ The unit beeps x The air conditioner starts cooling if the room temperature is higher than the selected temperature. Press the Press the button on the remote control. button on the remote control. 4 HIGH LOW To set the fan speed to. . . High Low FAN SPEED Result: Each time you press a button, the unit beeps. 5 To control the direction of the air flow, refer to page 11. E-8 Heating Your Room ENGLISH You must select the Heat mode if you wish to heat your room to a specific temperature. You can also set the fan speed. 1 If necessary, press the Result: (On/Off) button. Remote Control Control Panel x The operating mode indicator (COOL, HEAT or FAN) on the unit comes on. x The air conditioner starts up in the mode selected when the unit was last used. x The unit beeps twice. POWER air Theunit conditioner is fitted with a protection mechanism to prevent the from being damaged when it is started immediately after being: x Plugged in x Stopped It will start up automatically after a three-minute rest period. 2 If the HEAT indicator is not lit up on the unit: x Press the button on the remote control or x Press the MODE button on the unit one or more times until the HEAT indicator lights up Result: x The unit beeps each time you press MODE. x The air conditioner starts up in Heat mode. RESTART COOL FAN MODE POWER 3 You can change modes at any time. To adjust the temperature, press the or buttons on the remote control one or more times until the required temperature is displayed. To adjust the temperature, press the TEMPERATURE button on the unit one or more times until the required temperature is displayed. --> 29°C --> 30°C --> 16°C --> 17°C --> . . . . Possible temperatures are between 16°C and 30°C inclusive. High indoor and outdoor temperatures If both the indoor and outdoor temperatures are high and you select the Heat mode, the fan and compressor in the unit may stop at times. This is normal; simply wait until the air conditioner switches on again. If a power failure occurs when the air conditioner is operating, the unit is switched off. When the power returns, AZ09F7KE LRFC25750WW AZ09F8KE AZ09A8KE you must press (On/Off) button to restart it. the air conditioner starts up again automatically and the restart indicator blinkes for 2 minutes and then lights up. Warm air circulation Frost Power failure E-13 Temperature and Humidity Ranges The following table indicates the temperature and humidity ranges within which the air conditioner can be used. Mode Cooling Heating Indoor Temperature 21°C to 32°C approx. The automatic protection feature may be triggered and the air conditioner stopped. A water leakage or some other malfunction may happen if the heat exchanger freezes. Water may condense on and drip from the surface of the unit if it is used for long periods. Outdoor Temperature 21°C to 43°C approx. Indoor Humidity 80% or less - If the air conditioner is used at. . . [. . . ] The air conditioner does not operate with the remote control No beep is heard when you press (On/Off) on the remote control The air conditioner does not cool or heat (On/Off) on x Check that there are no obstacles between you and the unit. x Replace the remote control batteries if necessary. x Check that you are close enough to the unit (seven metres/yards or less). x Check that you are pointing the remote control at the remote control sensor on the unit. x Replace the remote control batteries if necessary. [. . . ]