User manual LG LRNV096SRA0

[. . . ] CONSTRUCTION VIEWS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPECIFICATIONS OF ELECTRICAL PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . REFRIGERANT CYCLE DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · A place which allows the front panel to be opened. 10-3-2. Drilling and Mounting Installation Plate Drilling When install the refrigerant pipes from the rear. The center of the pipe hole CAUTION · The indoor unit shall be installed so that the top of the indoor unit is positioned at least 2m in height. Also, avoid putting anything on the top of the indoor unit. · Direct sunlight on the indoor unit wireless receiver should be avoided. · The microprocessor in the indoor unit should not be too close to r-f sources. (For details, see the owner's manual. ) 42 mm Pipe hole 65 mm Fig. Decide the installation plate mounting position on the wall. Mark the corresponding pipe hole wall positions according to the positioning marks ( ð ) on the installation plate. Drill the pipe holes (Ø65 mm) slightly slanted downward to the outside. Remote controller · Should be placed where there are no obstacles, such as curtains, that may block the signal. · Do not install the remote controller in a place exposed to direct sunlight or close to a heating source, such as a stove. · Keep the remote controller at least 1 m away from the nearest TV set or stereo equipment. · In case of block, brick, concrete or similar type walls, drill 5 mm dia. · Insert clip anchors for the mounting screws. CAUTION · Be sure to refer to the wiring system diagram labeled inside the front panel. · Check local electrical regulations for any specific wiring instructions or limitations. NOTE : · Install the installation plate using between 4 to 6 mounting screws, making sure all four corners are secure. ­ 59 ­ 10-3-5. Piping and Drain Hose Installation Terminal cover Screw Piping and drain hose forming · Since condensation results in machine trouble, make sure to insulate both the connecting pipes separately. (Use polyethylene foam as insulating material. ) Rear right Screw Terminal block Earth wire Connecting cable Left Bottom right Fig. Die-cutting front panel slit Cut out the slit on the left or right side of the front panel for the left or right connection and the slit on the bottom left or right side of the front panel for the bottom left or right connection with a pair of nippers. Changing drain hose For left connection, left-bottom connection and rear-left connection's piping, it is necessary to relocate the drain hose and drain cap. Earth screw Fig. 10-3-7 Connecting cable How to remove the drain cap Clip drain cap with needle-nose pliers, and pull out. About 15 cm Fig. 10-3-11 110mm 10mm Earth line How to remove the drain hose The drain hose is secured in place by a screw. Remove the screw securing the drain hose, then pull out the drain hose. 10mm 50mm Fig. 10-3-9 NOTE : · Connecting cable (Indoor unit/outdoor unit) · Wire type: H07RN-F or 60245IEC66 (1. 0 mm²) Screw Fig. [. . . ] 223 224 225 226 227 229 230 232 233 234 237 238 239 240 243 245 246 248 Part No. 43049674 43047673 43044821 43044822 43039324 43019904 43049770 43062256 43062247 43082293 43083071 43003311 43070188 43079268 43066016 43080528 43080563 4308N972 Description Spring (16SKVP-ND) Pipe Ass'y, Connecting, Liquid Evaporator Ass'y (10SKVP-ND, 13SKVP-ND) Evaporator Ass'y (16SKVP-ND) Guide, Drain Holder, Sensor Holder, Evaporator, Right Cover, Terminal Cover, Lead Plate, Installation Holder, Remote Controller Body Ass'y, Back Hose, Drain Cap, Drain Remote Controller, WH-H05JE Plasma Pure Filter Generator Ass'y, HV Owner's Manual ­ 110 ­ 402 411, 412, 413 403 406 404 405 410 401 The parts in the following parts list are conformed to RoHS. Therefore be sure to use the following parts for repairing and replacing. 4306A132 43062263 43050425 43050426 4306S936 43051350 Description Terminal Block, 3P Cover, E-Parts Sensor, TC (Ø6), TCJ (Ø6) Sensor, TA P Board Ass'y, WRS-LED . C. [. . . ]