User manual LG LRNV186VBA0

[. . . ] Instead, they are requested to directly contact a designated service center or the outlet at which the product was purchased. Never spill any kind of liquid into the unit. Should this happen, unplug or main switch off the unit and contact an authorized service center. Do not insert anything between the air outlet blades because the inner fan may be damaged and could cause injury. [. . . ] 1 If necessary, press the Result: button. The operation indicator on the indoor unit lights up. The air conditioner starts up in the mode selected when the unit was last used. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: Plugged in Stopped lt will start up normally after three minutes. IMPORTANT 2 If the is not displayed at the top of the remote control, press the button on the remote control one or more times until it appears. Result: The indoor unit beeps each time you press the The air conditioner runs in the Auto mode. The Auto mode cools the room in optimum condition by adjusting the indoor temperature depending on the set temperature. button. Note 3 To adjust the temperature, press the button one or more times until the required temperature is displayed. Possible temperatures are between 16°C and 30°C inclusive. Result: Each time you press the button: - The temperature is adjusted by 1°C - The indoor unit beeps E-8 Cooling Your Room You must select the Cool mode if you wish to adjust the: Cooling temperature Fan speed when cooling 1 If necessary, press the Result: button. The operation indicator on the indoor unit lights up. The air conditioner starts up in the mode selected when the unit was last used. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: Plugged in Stopped lt will start up normally after three minutes. IMPORTANT 2 If the is not displayed at the top of the remote control, press the button on the remote control one or more times until it appears. Result: The indoor unit beeps each time you press the The air conditioner runs in the Cool mode. The indoor unit beeps. 2 Press the Result: button. The temperature and fan settings are adjusted automatically. The air conditioner cools the room as quickly as possible. After 30 minutes, the air conditioner is reset automatically to the previous mode, temperature and fan settings. You can select the Turbo function in the Auto and Cool mode. If you select this function in the Dry or Fan mode, it will return to the Auto mode. 3 If you wish to stop the Turbo function before the end of the 30-minute period, button one or more times until disappears. press the Result: The air conditioner is reset automatically to the previous mode, temperature and fan settings. 4 To control the direction of the air flow, refer to page 13. E-12 Adjusting the Air Flow Direction Vertically Depending on the position of the indoor unit on the wall of your room, you can adjust the position of the outer air flow blade on the bottom of the unit, thus increasing the efficiency of the air conditioner. 1 Press the Result: button one or more times as required. The outer blade is adjusted vertically. 2 If you want the blade to move up and down automatically when the air conditioner is operating, press the button. Result: The blade move up and down, around the base position set. 3 To stop the blade moving up and down, press the button again. Note If you switch the air conditioner. . . Set to the initial position powered. Adjusting the Air Flow Direction Horizontally There are two sets of inner air flow blades. [. . . ] 16°C to 32°C approx. Indoor Humidity 80% or less - If the cooling operation is used at over 32°C(indoor temperature), it does not cool at its full capacity. Operating Your Air Conditioner Without the Remote Control Your air conditioner can be operated directly from the indoor unit if the remote control is lost or broken. 1 To switch the air conditioner on, press the ON/OFF switch on the right side of the indoor unit. Result: The OPERATION indicator on the indoor unit comes on. The air conditioner starts up in the appropriate mode for the room temperature. 2 To switch the air conditioner off, press the ON/OFF switch again. Note Even if the air conditioner has been switched on via the ON/OFF switch, operations can still be controlled using the remote control as usual. E-17 ENGLISH Solving Common Problems Before contacting the after-sales service, perform the following simple checks. They may save you the time and expense of an unnecessary call. [. . . ]