User manual LG LRS-276GPASGQNG

[. . . ] Keep children away from the unit. 5 If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. 6 Do NOT attempt to repair the unit yourself. If it is damaged in any way, contact: x An authorized service center x The dealer from whom you purchased the air conditioner. 7 Do NOT place any blocking objects in front of the unit. 8 If the remote control will not be used for a long time, remove the batteries. [. . . ] x If the room temperature reaches the set temperature, the air conditioner stops cooling, but the fan is still operating. 4 To set the fan speed: x Press the button on the unit one or more times until the desired the Fan speed(F1, F2 or F3) is displayed. Low Medium High 5 To control the direction of the air flow, refer to page 20. E-9 Ventilating Your Room If the air in your room is stale, you can ventilate the room using the Fan feature. 1 If you wish to discharge stale air, push the ventilation lever on the front of the unit to the right and open position ( Result: ). x The air inside the room circulates and stale air is discharged outside. ). Otherwise, push the ventilation lever to the left and closed position ( Result: x The air simply circulates inside the room. 2 If necessary, press the Result: (On/Off) button. x The air conditioner starts up in the mode selected when the unit was last used. x The unit beeps twice. 3 If the fan speed(F1, F2 or F3) is not displayed on the control panel: x Press the button on the unit one or more times until the fan speed (F1, F2 or F3) is displayed. Result: x The unit beeps each time you press the button. x The air conditioner starts up in the Fan mode. When the air conditioner is in the Fan mode, the temperature cannot be set or displayed. 4 To set the fan speed: x Press the button on the unit one or more times until the desired fan speed(F1, F2 or F3) is displayed. Low Medium High 5 To control the direction of the air flow, refer to page 20. E-10 Removing Excess Humidity If the atmosphere in your room is very humid or damp, you can remove excess humidity without lowering the room temperature too much. You can operate the Dry mode only by using the control panel. 1 If necessary, press the Result: (On/Off) button. x The air conditioner starts up in the mode selected when the unit was last used. x The remaining time is displayed on the remote control and the control panel. x Blinking of the timer indicator on the remote control stops. x The timer indicator lights up on the control panel. x The unit beeps x The air conditioner will switch off automatically when the counter displayed on the remote control and the control panel reaches the set time. You can select the fan speed, temperature and Energy saving mode after setting the Off timer mode. However, when you change the mode, the Off timer mode is canceled. Control Panel To Cancel the Off Timer 1 Press the (Set/Cancel) button. If you want to turn off the air conditioner before the timer reaches the setting time, press the (On/Off) button. E-17 Setting the Sleep Timer The Sleep Timer can be used when you are cooling to switch the air conditioner off automatically after a period of 8 hours. Remote Control 1 2 If you wish to switch the unit off at a specific time, refer to page 17. Make sure that you have selected the Cool mode. Press the Result: x x x x button on the remote control. Each time you press a button, the unit beeps. The indicator on the remote control is displayed. The timer indicator lights up on the control panel. The "SLEEP" passes through the control panel for about 15 seconds and the " " will be displayed. [. . . ] Then lift it up slightly to open the front grille completely. 2 Grab the tabs on the filter and pull it up and out. 3 Remove all dust on the air filter with a vacuum cleaner or brush. 4 When you have finished, insert the air filter back into its original position. 5 Wipe the surface of the unit with a neutral detergent and then wipe it again with dry cloth. (Be sure not to use benzene, solvent or other chemical products. ) If you. . . Will not be using the air conditioner for a long period of time Then. . . x Set the fan going for a few hours to dry the inside of the air conditioner thoroughly. x Switch the air conditioner off and unplug it from the wall socket. Set the fan going for a few hours to dry the inside of the air conditioner thoroughly. Have not used the air conditioner for a long period of time E-22 Solving Common Problems Before contacting an authorized service center, perform the following simple checks. [. . . ]