User manual LG LS-C1264DM1

[. . . ] (If applicable) The air conditioner must be plugged into its own specific power source, which must be installed in compliance with national wiring, earthing and safety regulations. DURING OPERATION If the power cord is damaged in any way, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard. This device must be installed according to the national electrical rules. The appliance must be installation that the plug should be easily accessible after installation. If the fuse on PC board is broken please change it with the type of T 3. 15A 250V. [. . . ] Usually, the maximum permissible mains impedance will not be exceeded when the branch to the power outlet is fed from a junction box with a rated current of 32A. AW18 ** E-3 ENGLISH Air Conditioning Unit - Main Parts and Control Panel The desing and shape are subject to change according to the model. Air Outlet Inner air flow blades (right/left orientation) Air inlet(Inside) The air filter is located in side Outer air flow blades (up/down orientation) Air inlet (Outside) Ventilation lever Power Cable Power plug The type of the power plug may differ according to the type of local power supply. Operating mode selection dial Temperature control dial Coolest Air flow blade swing switch E-4 Cooling Your Room ENGLISH You must select the Cool mode if you wish to lower the temperature in your room. 1 Select the operating mode and fan speed. Set the operating mode selection dial to. . . High fan speed Between HIGH and LOW Low fan speed Result: HI COOL MED COOL LOW COOL The air conditioner starts up in Cool mode. The fan starts up at the speed selected. 2 To adjust the temperature, turn the temperature control dial to the desired position. Possible temperatures: Between 18 C and 29 C inclusive. Result: The air conditioner starts cooling if the room temperature is higher than the selected temperature. 3 To control the direction of the air flow, refer to page 7 E-5 Airing Your Room If the atmosphere in your room is stale, you can air it using the Fan feature and if necessary, evacuate the stale air outside. 1 If you wish to evacuate stale air outside, push the ventilation lever on the front of the unit to the right and the open position ( ). Result: The air inside the room circulates and stale air is evacuated outside. 3 Reassembling of front grille should be done in reverse order of disassembly. 2 Pull the air filter to the right side. 3 Remove all dust on the air filter with a vacuum cleaner or brush. 4 When you have finished, insert the air filter back into its original position. 5 Wipe the surface of the unit with a neutral detergent and then wipe it again with dry cloth. (Be sure not to use benzene, solvent or other chemical products. ) The air conditioner has two or three grille grooves depending on the model. Will not be using the air conditioner for a long period of time Then. . . Set the operating mode selection dial to "LOW FAN" and let it run of a few hours to dry the inside of the air conditioner thoroughly. Switch the air conditioner off and unplug it from the wall socket. Set the operating mode selection dial to "LOW FAN" and let it run of a few hours to dry the inside of the air conditioner thoroughly. Have not used the air conditioner for a long period of time E-8 Solving Common Problems ENGLISH Before contacting the after-sales service, perform the following simple checks. They may save you the time and expense of an unnecessary call. PROBLEM The air conditioner does not operate at all EXPLANATION / SOLUTION Check that the circuit breaker used for the air conditioner has not been triggered. Check that the power cable is plugged into a wall socket and the socket is switched on, if necessary. Check that the correct operating mode has been selected (cooling or airing). The air conditioner does not cool Check that the correct operating mode has been selected. [. . . ] Follow national electrical codes or local codes and ordinances. 115V 15 AMP Circuit "parallel" type 230V/208V 20 AMP circuit "perpendicular" type 230V/208V 15AMP circuit "tandem" type 230V/208V 30 AMP circuit "tandem" type If the electric supply provided does not meet the above specifications, call a licensed electrician. Aluminum house wiring may pose special problemsconsult a qualified electrician. This unit requires a separate circult, serving only this appliance. E-11 Installation Before installation, be sure to check the installation area for the air conditioner, and drain hose. Checkpoints prior to installation 1 Check the cabinet and front grille of the unit for any harmful defects such as scratches. [. . . ]