User manual LG LS-C1825DA1

[. . . ] - To reduce the risk of damage, electric shock, and fire, Introduction Front Connecting the Cables 1. (if the compartment does not open when you press the Eject button, power off the computer, insert a pin or unfolded paper clip in the hole and push firmly) 2. (When it is green, a disc is being read. ) 3. (the compartment opens and closes automatically when you press the Eject button) Introduction Rear Connecting the Cables 1. [. . . ] Remove the cover from a free expansion slot and install the DVD-ROM drive, as shown in the illustration. Setup Connecting the Cables Connecting the Cables Connecting the power cable The 4-pin power cable from the internal power unit of your computer must be connected to the power terminal on the rear of the Optical drive drive. 1 +5V DC 2 Ground A - Cut S-IDE 3 Ground 4 +12V DC Note: An improperly connected power cable may cause trouble. Check the direction of the power connector and the incline S-IDE of the Optical drive before connecting. Connecting the E-IDE cable Insert the E-IDE cable (40-pin), which is connected to the hard disk to the interface terminal. (Place the red line of the cable close to the Pin 1. ) When using one E-IDE cable Connect the cable to the SL (Slave) of the Master/Slave Select Terminal at the rear of the Optical drive. a : Slave Drive (Choose the SL Jumper) b : Hard Drive c : MainBoard When using two E-IDE cable If there is only one Optical drive, select MA (Master). Setup a : Master Drive (Choose the MA Jumper) c : MainBoard e : Secondly 1 b : Hard Drive d : Primary 1 If there is two Optical drive, select MA (Master) / SL (Slave). a : Master Drive (Choose the MA Jumper) b : Slave Drive (Choose the SL Jumper) c : Hard Drive e : Primary 1 d : MainBoard f : Secondly 1 Installing a jumper on the master/slave select terminal Setup Connect a jumper to the rear S-IDE of the Optical drive. If the jumper is connected to MA (Master), it will work in the Master mode. If the jumper is connected to SL (Slave), it will work in the Slave mode. If the jumper is connected to CS (CSEL), you can control the device by using the host interface signal CSEL. (In general, connection to MA is recommended. ) Connecting the audio cable from a sound card Connect the 4-pin audio cable between the sound output terminal on the Optical drive and the audio input terminal on the sound card. For clearer sound, use a digital output terminal. (Available only for the CARD that supports digital output) This may not be available for general sound cards. Setup Installing the Device Driver This Device Driver is an installation driver that can detect ODD (Optical Disc Drive) products in DOS mode. It provides only the reading function in Dos mode. (For recording, it is recommend not to install the Device Driver designed for DOS mode) The Device Driver for DOS mode is included in the Ddriver or DOS Driver folder of the disc enclosed with the product that you purchased. For Windows98/2000/ME/XP or higher version that uses a device driver provided by Windows, there is no need to set up an extra device driver. Refer to the steps below to see if Windows detects the drive. Currently, the motionpicture industry has divided the worldinto different regions or zones thatcorrespond to the regional markets intowhich the motion picture industry releasesmovies. Simply put, RPC codes are placedon movies marketed throughout the world, based on the region of the world inwhich they are being sold. These RPCcodes help control and prevent piratingof new movies into other motion pictureregions prior to their true releasedates within those markets. In the RPC-2 mode, the localcode can be changed by users. RPC-2is selected by default for the DVD-ROM drive. You can change the region code up tofive times via an MPEG application. Please contact your dealer or local LG representative if you wish tochange the local code more than fivetimes. Troubleshootin Connecting the Cables Problem The DVD-ROM drive is not detected by the computer. After installing the DVD-ROM drive, the PC gets slower. Meaning / Solution Check that the power, audio and IDE cables are correctly connected to the computer. Change the IDE cable and reconnect it to the computer. Preferably, connect a second IDE cable to the DVD-ROM drive in master mode. Check the position of the jumper in the master/slave select terminal. The DVD-ROM drive is not recognized by MS-DOS. Reinstall the device driver or update it with the latest version by downloading it from the Samsung Web site. [. . . ] No sound is heard from an audio CD. A CD is not read or is read too slowly. The disc compartment will not open. Check whether the CD is of good quality and clean it, if necessary. Check that the power cable is correctly connected. Insert a pin or unfolded paper clip in the emergency hole and push firmly until the disc compartment opens. When the MPEG software plays a Video CD, the pictures are not regular and the running speed is too slow. [. . . ]