User manual LG LS-H1865DM1

[. . . ] 14 1-EN ­1­ Wireless Remote Controller Kit Owner's Manual 1 PRECAUTIONS FOR SAFETY WARNING WARNINGS ABOUT INSTALLATION · Make sure to ask the qualified installation professional in electric work to install the remote controller. If the remote controller is inappropriate installed by yourself, it may cause electric shock or fire, etc. · Make sure to install the air conditioner specified by LGand ask the exclusive dealer when installing. If the air conditioner is installed by yourself, it may cause electric shock or fire, etc. [. . . ] (When a trouble occurs, the check code is displayed. ) 4 5 Filter display If "FILTER filter. " is displayed, clean the air 10 Timer SET IN setup display When pushing the Timer SET IN button, the display of the timer is selected in order of [OFF] [OFF] repeat OFF timer [ON] No display. CHECK display Displayed while the protective device works or a trouble occurs. ­5­ 5-EN Wireless Remote Controller Kit Owner's Manual Operation section Push each button to select a desired operation. · The details of the operation needs to be set up once, afterward, the air conditioner can be used by pushing ON/OFF only. 1 2 3 ADR 5 6 7 EN 4 1 2 3 4 5 Operation select button Selects the desired operation mode. ACL SENSOR 6 Start/Stop button When the button is pushed, the operation starts, and it stops by pushing the button again. When the operation has stopped, the operation lamp and all the displays disappear. Fan mode select button Selects a fan mode. Time setup button Used for timer setting. (See page 8) Check button The CHECK button is used for the check operation. During normal operation, do not use this button. 7 Filter button Resets (Erases) "FILTER " display. OPTION : Remote controller sensor Usually the temperature sensor of the indoor unit senses the temperature. The temperature on the surrounding of the remote controller can also be sensed. For details, contact the dealer from which you have purchased the air conditioner. Temperature set button Adjusts the room temperature. Set the desired set temperature by pushing or . ­6­ 6-EN Wireless Remote Controller Kit Owner's Manual 3 HOW TO OPERATE INDOOR UNIT Auto, Heat, Dry, Cool, Fan 5 Stop Push . When the operation is stopped with the remote controller, the outdoor unit fan keeps running in some cases even after the compressor of the outdoor unit has stopped. · The automatic cooling/heating and heating functions are not provided for cool-only types. For details of slide switch setting, contact the dealer from whom you purchased the air conditioner. 7 1 2 3 HOW TO INSERT BATTERIES Slide and remove the cover downward while holding both sides of the cover. Insert two AAA alkaline batteries correctly matching the (+) and (-) polarities with the indication. Push the RESET button with a fine-tipped tool and attach the cover. · Replace batteries when the display on the remote controller has become dim or when signals from the remote controller cannot be received at the normal distance from the signal receiving part. Alkaline batteries should be replaced once a year. · Replace two batteries at the same time with new ones of the same type. · When you do not use the remote controller for a long time, take out the batteries. · Discard exhausted batteries at a designated place. ­ 10 ­ RESET button Cover 10-EN Wireless Remote Controller Kit Owner's Manual 8 HOW TO HANDLE THE REMOTE CONTROLLER · Point the transmitting part of the remote controller at the signal receiving part of the indoor unit. When a signal is received normally, "pi" sound is heard once. ("Pi, pi" is heard only at the beginning of operation. ) · The standard signal receivable distance from the signal receiving part of the indoor unit is approx. The distance varies somewhat with the battery capacity or other conditions. [. . . ] Transmit signals while pointing the remote controller at the signal receiving part of the indoor unit to be controlled. EN Matching Addresses Address setting on the remote controller 1. "Address" lights up on the display and the current address flashes. 2. Each time you push ADR , addresses change cyclically like ALL 1 2 3. . . Select an address that matches the address switch setting in the signal receiving part of the indoor unit to be controlled. [. . . ]