User manual LG LS-K2461QC

[. . . ] Instead, they are requested to directly contact a designated service center or the outlet at which the product was purchased. Never spill any kind of liquid into the unit. Should this happen, unplug or main switch off the unit and contact an authorized service center. Do not insert anything between the air outlet blades because the inner fan may be damaged and could cause injury. [. . . ] The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: Plugged in Stopped lt will start up normally after three minutes. IMPORTANT 2 If the is not displayed at the top of the remote control, press the button on the remote control one or more times until it appears. Result: The indoor unit beeps each time you press the The air conditioner runs in the Cool mode. button. Note 3 button one or more times until To adjust the temperature, press the the required temperature is displayed. Possible temperatures are between 16°C and 30°C inclusive. Result: Each time you press the button: - The temperature is adjusted by 1°C - The indoor unit beeps The air conditioner starts cooling, provided that the room temperature is higher than the selected temperature. If the room temperature reaches the set temperature, the air conditioner stops cooling, but the fan is still operating. button one or more times ) 4 Select the fan speed by pressing the until the required setting is displayed: Automatic (rotated : Low Medium High Maximum Result: Each time you press the button, the indoor unit beeps. 5 To control the direction of the air flow, refer to pages 14. E-9 ENGLISH Heating Your Room You must select the Heat mode if you wish to adjust the: Heating temperature Fan speed when Heating 1 If necessary, press the Result: button. The operation indicator on the indoor unit lights up. The air conditioner starts up in the mode selected when the unit was last used. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: Plugged in Stopped lt will start up normally after three minutes. IMPORTANT 2 If the is not displayed at the top of the remote control, press the button on the remote control one or more times until it appears. Result: The indoor unit beeps each time you press the The air conditioner runs in the Heat mode. button. Note 3 button one or more times until To adjust the temperature, press the the required temperature is displayed. 1 To set the operating time, press the button one or more times until the required time is displayed. Possible time is between 0. 5 hour and 24 hour inclusive. 2 Press the Result: button to complete the setting. The selected mode and the temperature on the display disappear after 10 seconds. The air conditioner will switch on automatically when the counter displayed on the remote control reaches the set time and disappears the On Timer setting. 3 To select an operating mode in advance, press the button until the desired mode is displayed at the top of the remote control. Result: The air conditioner will run in the selected mode when it is turned on. If you don't operate the remote control after setting the On Timer, it will be turned off automatically after 25 hours. Note To Cancel the On Timer If you no longer wish to use the On Timer that you have set, you can cancel it at any time. 1 To cancel the On Timer, press the the timer setting disappears. button one or more times until 2 Press the button. If you want to turn on the air conditioner before the timer reaches the setting time, press the button. Note E-15 ENGLISH Setting the Off Timer The Off Timer enables you to switch off the air conditioner automatically after a given period of time. You can set the period of time from 0. 5 hour to 24 hours. 1 To set the operating time, press the button one or more times until the required time is displayed. [. . . ] Problem The air conditioner does not operate at all Explanation/Solution Check that the breaker used for the air conditioner is switched on. Check that the operation indicator on the indoor unit is on; if necessary press the button on the remote control. Check whether the Timer indicator on the indoor unit is switched on. If so: - Wait until the switch-on time is reached and the air conditioner starts up automatically - Cancel the timer (see pages 15 and 16 for further details) Check that there are no obstacles between you and the indoor unit. [. . . ]