User manual LG LS-K2466QCACASA

[. . . ] PARTS REPLACEMENT 10-1 Indoor Unit 10-2 Outdoor Unit 11. EXPLODED VIEWS AND PARTS LIST 11-1 11-2 11-3 11-4 11-5 11-6 Indoor Unit (E-Parts Assy) Indoor Unit Outdoor Unit (RAS-13UAH-ES2, RAS-13UAH-AS2) Outdoor Unit (LS-K2466QCACASA, RAS-10UAH-AS2) Outdoor Unit (RAS-13UA-ES2, RAS-13UA-AS2) Outdoor Unit (RAS-10UA-ES2, RAS-10UA-AS2) · This air conditioner is charged with HFC (R410A) that doesn't deplete the Ozone layer. · This air conditioner requires special installation for the refrigerant R410A. ­2­ FILE NO. SPECIFICATIONS MODEL ITEM Capacity 220V kW Phase Power source Power consumption Power factor Running current Indoor Outdoor V Hz kW % A A A lit/h dB dB kg mm mm 49 51 1. 00 Capillary tube 12. 7 Flare connection 6. 35 Flare connection m m RAS-13UKHP-ES2, AS2 Height Dimensions Net weight Evaporator type Indoor fan type High fan Air volume Medium fan Low fan Fan motor output Air filter OUTDOOR UNIT Height Dimensions Net weight Condenser type Outdoor fan type Airflow volume Fan motor output Compressor Safety device Louver type Usable outdoor temperature range °C 15 ~ 43 Model Output W m /h W 3 RAS-13UKHP-ES2, AS2 RAS-13UAH-ES2, AS2 Cooling 240V 3. 60 220V 4. 20 1 220 ­ 240 50 1. 10 98 4. 95 1. 12 97 4. 65 27 2. 0 41/35/31 49 R410A 51 1. 14 97 0. 15 5. 20 4. 95 1. 18 96 3. 60 Heating 240V 4. 26 RAS-13UKP-ES2, AS2 RAS-13UA-ES2, AS2 Cooling 220V 3. 75 240V 3. 75 1. 13 98 5. 10 28 1. 17 97 4. 90 Starting current Moisture removal Noise Refrigerant Indoor (H/M/L) Outdoor (220-240V) Name of refrigerant Rated amount Gas side size Connection type Liquid side size Interconnection Connection type pipe Maximum length (One way) Maximum height difference INDOOR UNIT 49 0. 97 50 Refrigerant control 15*1 6 RAS-13UKP-ES2, AS2 275 790 208 10 Finned tube Cross flow fan mm mm mm kg Width Depth m3/h m /h m3/h W 3 630 520 430 650 550 490 20 Honeycomb woven filter with PP frame RAS-13UAH-ES2, AS2 630 520 430 RAS-13UA-ES2, AS2 550 780 270 mm mm mm kg 40 Width Depth 37 Finned tube Propeller fan 2120 2200 2120 42 2200 2120 2200 PA150X2T-4FM1 1100 Fuse, Overload relay Automatic louver ­10 ~ 24 15 ~ 43 ­3­ FILE NO. [. . . ] 8-4-17 CAUTION Firmly insert the drain hose and drain cap; otherwise, water may leak. <In case of right or left piping> · After scribing slits of the front panel with a knife or a making-off pin, cut them with a pair of nippers or an equivalent tool. Fig. 8-4-14 How to install the drain hose Firmly insert drain hose connecting part until hitting on a heat insulator. Slit Fig. 8-4-18 <In case of bottom right or bottom left piping> Heat insulator · After scribing slits of the front panel with a knife or a making-off pin, cut them with a pair of nippers or an equivalent tool. Drain hose Fig. SVM-03001 <Left-hand connection with piping> 8-4-6. Indoor unit fixing Bend the connecting pipe so that it is laid within 43 mm 1. Pass the pipe through the hole in the wall, and hook above the wall surface. If the connecting pipe is laid the indoor unit on the installation plate at the upper exceeding 43 mm above the wall surface, the indoor hooks. Swing the indoor unit to right and left to confirm that connecting pipe, make sure to use a spring bender so it is firmly hooked up on the installation plate. While pressing the indoor unit onto the wall, hook it at the lower part on the installation plate. Pull the Bend the connection pipe within a radius of 30 mm. When connecting extension drain hose, insulate the connecting part of extension drain hose with shield pipe. Shield pipe CAUTION 1. Install the outdoor unit without anything blocking the air discharging. When the outdoor unit is installed in a place exposed always exposed to strong wind like a coast or on a high storey of a building, secure the normal fan operation using a duct or a wind shield. In particularly windy areas, install the unit such as to avoid admission of wind. Installation in the following places may result in trouble. · A saline-place such as the coast. · A place where high-frequency waves are likely to be generated as from audio equipment, welders, and medical equipment. Drain hose Inside the room Extension drain hose Fig. 8-4-24 CAUTION Arrange the drain pipe for proper drainage from the unit. Improper drainage can result in dew-dropping. This air conditioner has the structure designed to drain water collected from dew, which forms on the back of the indoor unit, to the drain pan. Therefore, do not store the power cord and other parts at a height above the drain guide. Wall Drain guide Strong wind Space for pipes Fig. [. . . ] 2) Remove the 2 screws fixing the base bearing. 3) Remove the bearing from the base bearing. If the housing protrudes from the base bearing, put the housing in position and attach the bearing to the base bearing. 2 2-Screws ­ 64 ­ FILE NO. 1 Part name Common procedure Procedures 1) Stop the operation of air-conditioner, and disconnect the power cord from the AC supply. [. . . ]