User manual LG LS-L1260CL

[. . . ] : Warning and Caution are to call the users attention to the possible danger. Read and follow them carefully in order to prevent a safety accident. : Warning and Caution are indicated in this guide and the product itself to help protect the users from danger. WARNING Installation Replace the all batteries in the remote control with new ones of the same type. Do not mix old and new batteries or different types of batteries. [. . . ] - Setting range : 00 ~ FF Group No. Indoor Unit No. 3 4 5 1 2 3 After setting the address, press the ON/OFF button toward the indoor unit 1 time. The indoor unit will display the set address to complete the address setting. - The address display time and method can differ by the indoor uint type. Reset the remote controller to use the general operation mode. Installer Setting - Checking Address of Central Control With the PLASMA button pressed, press the RESET button. Press the ON/OFF button toward the indoor unit 1 time, and the indoor unit will display the set address in the display window. - The address display time and method can differ by the indoor unit type. Reset the remote controller to use the general operation mode. 8 Wireless Remote Controller Installation Instruction ENGLISH Installer Setting -How to enter installer setting mode CAUTION Installer setting mode is to set the detail function of the remote controller. If the installer setting mode is not set correctly, it can cause problems to the product, user injury or property damage. This must be set by an certificated installer, and any installation or change that is carried out by a non-certificated person should be responsible for the results. In this case, free service cannot be provided. 1 2 With the FAN SPEED button pressed, press the RESET button. By using the TEMPERATURE SETTING button, set function code and setting value. (Please refer the Installer Setting Code Table. ) Function Code Setting Code 3 4 Press the ON/OFF button toward the indoor unit 1 time. Reset the remote controller to use the general operation mode. Refer to the Installer Setting Code Table on the next page. Owners & Installation Manual 9 Installation Instruction Installer Setting - Installer Setting Code Table Installer Setting Code Table No. 0 Function Mode Override Function Code Setting Value 0 : Set to Master 1 : Set to Slave 1 : Standard 1 Ceiling Height Selection Remote Controller LCD 0 1 2 : Low 3 : High 4 : Super High 0 : Set to Master Group Control 2 2 1 : Set to Slave 2 : Check Master/Slave 3 : Set to Auxiliary heater Auxiliary heater 2 4 : Cancel Auxiliary heater 5 : Check Auxiliary heater Installation Mode Override This Function is only for Non-Auto Changeover H/P model. Ceiling Height Selection Indoor unit connected to wired remote controller operate as wired remote controller setting. Group Control This function is only for group control. Please dont set this function in case of non-group control. After setting Group Control of the product, turn off the power then turn it back on after 1 minute. Auxiliary heater This function is only applied to models with Auxiliary Heater function being activated. 10 Wireless Remote Controller Owner's Instruction ENGLISH Owner's Instruction Cooling Mode - Standard Operation 1 2 3 Press the ON/OFF button. You can select the fan speed in four steps­low, medium, high, or chaos. Each time the button is pressed, the fan speed mode is shifted. Natural Wind by the chaos Logic · For more fresh feeling than other fan speed, press the Indoor Fan Speed Selector and set to chaos mode. In this mode, the wind blows like natural breeze by automatically changing fan speed according to the chaos logic. During Fan Mode · The outdoor compressor doesn't work. Have a function to circulate the indoor as it sends out the air that doesn't have much temperature difference with indoor. Owners & Installation Manual 17 Temperature Setting/Room Temperature checking Temperature Setting/Room Temperature checking We can simply adjust the desired temperature · Press the buttons to adjust the desired temperature : Increase 1°C or 2°F per one time pressing : Decrease 1°C or 2°F per one time pressing Room temp: Indicate the current room temperature Set temp: Indicate the temperature that user want to set <Cooling Mode> The cooling mode doesn't work if desired temperature is higher than room temperature Please lower the desired temperature <Heating Mode> The heating mode doesn't work if desired temperature is lower than room temperature Please increase the desired temperature Whenever press button, the room temperature will be displayed within 5 seconds. After 5 seconds, it turns to display the desired temperature. Because of location of remote controller, the real room temperature and the this displayed value can be different. 18 Wireless Remote Controller Airflow Setting ENGLISH Airflow Setting Up/Down Airflow Direction Control (Optional) The up/down airflow (Vertical Airflow) can be adjusted by using the remote controller. Press the ON/OFF button to start the unit. Press UP/DOWN AIRFLOW button and the louvers will swing up and down. Press the UP/DOWN AIRFLOW button again to set the vertical louver at the desired airflow direction. NOTE · If you press the UP/DOWN AIRFLOW button, the horizontal airflow direction is changed automatically based on the Auto Swing algorithm to distribute the air in the room evenly and at the same time to make the human body feel more comfortable, as if enjoying a natural breeze. · Always use the remote controller to adjust the up/down airflow direction. Manually moving the vertical airflow direction louver by hand, could damage the air conditioner. [. . . ] If the Auto Clean function is reserved, whenever the unit is turned off, the indoor fan is still running for about 30 minutes internally without cooling or dehumidification operation. This dries up any remains of moisture & cleans the unit internally. 20 Wireless Remote Controller Sub function ENGLISH Smart Clean (Optional) The Smart Clean function can be used by setting to manual or automatic. Auto Smart Clean operation If the accumulated operation time of the product exceeds 30 hours, the Smart Clean automatically starts when the unit is turned off. Press the FUNCTION SETTING button 2 times. Press the SET/CLEAR button to reserve or cancel the Smart Clean function. [. . . ]