User manual LG LSN364H-4

[. . . ] You'll find many answers to common problems in the chart of troubleshooting tips. If you review our chart of Troubleshooting Tips first, you may not need to call for service at all. Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Operating Instructions. . . . . . . . . . . . . . . . . 12 Maintenance and Service . . . . . . . . . . . . 20 PRECAUTION Check Item prior to notify a failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 · Contact the authorized service technician for repair or maintenance of this unit. · Contact the installer for installation of this unit. · The ventilator is not intended for use by young children or invalids without supervision. [. . . ] When cleaning the unit, first make sure that the power and breaker are turned off. The fan rotates at a very high speed during operation. There is a possibility of injury if the unit's power is accidentally triggered on while cleaning inner parts of the unit. Service For repair and maintenance, contact your authorized service dealer. 8 Ventilator Introduction Introduction Symbols used in this Manual ENGLISH This symbol alerts you to the risk of electric shock. This symbol alerts you to hazards that could cause harm to the ventilator. NOTICE This symbol indicates special notes. Features WARNING: This appliance should be installed in accordance with national wiring regulations. This guide acts as a guide to help to explain product features. 5 1 6 2 3 7 4 8 1. Air Filter Prevents clogging of the Total heat exchanger due to dust. Total Heat Exchanger Exchanges temperature and moisture between air supply air and exhaust air. Blower for Exhausting A blower for draining polluted air outside. Control Box The figure of Total heat Exchanger can be different by the Product Model. Owner's Manual 9 6. Blower for Air Supply A blower for sucking outside air. Damper Plate Converts the ventilation via Total heat exchange to the normal ventilation. Timer Timer Cancel fresh Program Week Holiday Auto Set/Clr Hour Min TIME RESET 2 Press the [Minute] button on the adjustment part of the remote controller. Figures change 00 through 59 whenever you press the button. Adjust the current time. VENTILATOR OPERATION SUB FUNCTION Hi SHi Cover open status EXTERNAL Linked Run Dual Remote Central Run Heat XCH PLASMA e-SAVER fresh Auto Auto Delay Time Program set Auto Lo Heater Preheat Defrost Humidify ZONE 1234 Fri Sat Normal Fan Speed Time Sun Mon Tue Wed Thu Hour Min Set no. Timer 3 Press the [Week Day Select] on the adjustment part of the remote controller. Weekdays change from Sunday through Saturday whenever you press the button. Adjust the current day. VENTILATOR OPERATION SUB FUNCTION Hi SHi EXTERNAL Week Linked Run Dual Remote Central Run Heat XCH PLASMA e-SAVER fresh Auto Auto Delay Time Program set Auto Lo Heater Preheat Defrost Humidify ZONE 1234 Fri Sat Normal Fan Speed Time Sun Mon Tue Wed Thu Set no. Timer 4 Press the [Reset] button on the adjustment part of the remote controller. *If you press [RESET] button once, current time is set. And if you press it once again, current set time cancelled. TIME RESET Sun 16 Ventilator Operating Instructions Weekly Reservation Setup No reservation operation is done with the current time not setting up. Example) To operate the ventilator at 06:00 ~ 08:00 and 13:00 ~ 22:00 on Monday ENGLISH 1 EXTERNAL VENTILATOR OPERATION SUB FUNCTION Hi SHi Press the [Program] button on the adjustment part of the remote controller. Linked Run Dual Remote Central Run Heat XCH PLASMA Timer On Off Set no. Timer e-SAVER fresh Auto Auto Delay Time Program set Auto Lo Heater Preheat Defrost Humidify ZONE 1234 Fri Sat Normal Fan Speed Filter Time Sun Mon Tue Wed Thu EXTERNAL VENTILATOR OPERATION SUB FUNCTION Hi SHi Program Linked Run Dual Remote Central Run Heat XCH PLASMA e-SAVER fresh Auto Auto Delay Time Program set Auto Lo Heater Preheat Defrost Humidify ZONE 1234 Fri Sat Normal Fan Speed Filter Time Sun Mon Tue Wed Thu Set no. [. . . ] - Total heat exchanger: More than once every 2 years (Cleaning cycle may increase according to pollution degree. ) Method to take each part out 1. Remove the maintenance cover. Put the hands inside of the ceiling from the maintenance cover, and pull the maintenance cover up. (Looser the hinge and detach the maintenance cover. ) Main Body 2. Take the air filter out. Take the air filter with each contained to the left/right downside of the Total heat exchanger. [. . . ]