User manual LG LST-4600A

[. . . ] LGE reserves the right to make changes in technical and product specifications without prior notice. 3 Table of Contents 1 Before You Start Safety Instruction Optimal Phone Performance Care and Service Safety Information 7 7 7 8 9 2 Introduction Component List Front, Side and Rear View of the Terminal 3 LEDs Indicators Installation Installation Steps 12 13 14 16 17 20 3 Basic Operation Power On Placing a call Receiving a call Ending a call Warning Tone after Remote Disconnect Emergency Call Power Off 21 21 21 22 22 22 22 23 4 System Features Hook flash ROH (Receiver Off Hook) System Features Applications 24 24 24 24 26 5 Table of Contents 5 Programming Speed Dial Emergency Call Hot Line Alarm Volume Level Outgoing Call Lock G3 FAX/DATA Mode Setting Restrict Call Mode Setting Before You Start Safety Instruction WARNING/CAUTION To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. Do not use this product near swimming pools or other water bodies. IMPORTANT Before installing or operating this product read this information. 27 27 29 30 31 32 32 33 35 Optimal Phone Performance 6 7 Troubleshooting General Information LST-255 37 38 38 Do not operate your product when holding the antenna, or when someone is within four inches (ten centimeters) of the antenna. Holding the antenna affects call quality and may cause the telephone to operate at a higher power level than needed. [. . . ] As long as your telephone is registered on a system, you can place a call to emergency number even if your telephone is locked or restricted. Please check the available emergency call number with your service provider. 22 23 System Features Hook flash When the terminal receives a hook-flash from the connected telephone device, it will automatically allow: 1. For producing dial tone again after a phone number has been dialed without connection. The use of special cellular services which may be available in your cellular service area. Note: - Hook-flash is accomplished in a call through either pressing the dedicated hook-flash key which is available on some phones or through a rapid single press of the hang-up mechanism upon which the handset rests when the phone is hung up. System Features Call Waiting - You can receive another incoming call during a call. In this case, you will hear beep tone and then you can connect the second call holding the first call by entering a code required by cellular service provider. Your cellular service provider may require hook-flash (a quick, simulated hang up ) to answer the waiting call. Other providers may require entering the codes involving digits 1-9, *, and # to answer a waiting call. Three-way Conference Calls - For three-way conference calls, a hook-flash transmits the SEND command. Please contact your cellular service provider for more information on using this service. Example Dial the first number and wait until connected: When connected, give hook-flash and dial the second number and give one more hook-flash to be connected: When the second call is connected, give hook flash to complete a 3-way conference call. ROH (Receiver Off Hook) If the telephone equipment remains off-hook , meaning that the handset is left off of its cradle as it would be when you hang up, with no dialing activity for about 60 seconds, a ROH tone emits from the receiver for a period of 60 seconds. After ROH tone, Line Lock Out Tone emits from receiver for a period of 60 seconds. This feature may be different or not by country specification. Voice mail - Use voice mail service in the same manner as you would on a regular telephone. Press # + # + 1 continuously to enter speed dial programming mode. Press # and 1 or 2 to enable or disable respectively. 1 - Speed Dial Enable 2 - Speed Dial Disable 3. Press * to store. # and one of the emergency memory location numbers (1~3). * to save and enable this function. Enable or Disable emergency call 1. Press # + # + 2 continuously to enter emergency call programming mode. Press # and Enable code ( 1 ) or Disable code ( 2 ). Press * to save. Erase All Speed Dials 1. Press # + # + 1 continuously to enter speed dial programming mode. Press * to store. Note1: Speed dial feature is disabled after erase operation executed Erase All Emergency Call Numbers 1. Press # + # + 2 continuously to enter emergency call programming mode. [. . . ] Press # and LOCK code (4 digits : set in Outgoing call lock). Press # and 1 to enter Permit Dial Number store step. Press # and one of Memory number for permit dial number(1~10). If you want to store more Permit Dial Numbers continue from step 3. [. . . ]