User manual LG LT1030HR

[. . . ] Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. · A suitable conduit entries, knock-outs or glands shall be provided in the cable entries of this product in the end user. Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equivalent type recommended by the manufacturer. [. . . ] Tighten the locking screw. Installation 31 NOTE You can install the PIPE Installation Bracket direct to the other type LG Wall Mount assembly. This LG Wall Mount assembly make to easy to install your camera. 3 Installation 32 Operation 4 Operation Setup Menu Overview The following table shows the list of menu items and options. You can adapt the camera to your requirements by setting up the respective items in these menus. 1st level 2nd level 3rd level FOCUS MODE FOCUS FOCUS DIST RETURN IRIS AGC WDR/BLC CAMERA SET EXPOSURE BRIGHTNESS SHUTTER SENS-UP RETURN ATW AUTO COLOR TEMP WHITE BALANCE MANUAL RED BLUE RETURN ONE PUSH INDOOR/OUTDOOR - 100 to +100 - 100 to +100 AUTO/MANUAL OFF/LOW/MIDDLE/HIGH OFF/WDR/BLC/HSBLC 0 to 100 OFF, A. FLK, 1/160, . . . , X2, AUTO AUTO X2/AUTO X3/. . . /AUTO X128/OFF Contents AUTO/MANUAL/ONE PUSH/ ZOOM TRIG LT913 Series : 50 CM, 1. 8 M, 3 M, 6 M LT713 Series : 50 CM, 1 M, 3 M, 5 M 4 Operation Operation 33 D/N LEVEL AUTO DAY/NIGHT DAY NIGHT OFF 3D-DNR LOW MIDDLE HIGH COLOR SHARPNESS RETURN NAME SPEED DWELL TIME IRIS WDR/BLC/HSBLC ON OFF 0 to 68 COLOR DWELL TIME RETURN LOW/MIDDLE/HIGH 5, 10, 15, 30, 60 SEC -20 to 20 OFF/ON 1 to 127 1 to 255 AUTO, 20, 40, 60, 80, 100 % OFF/ LOW WDR/ MID. HSBLC/ HIGH HSBLC X512, . . . , x2, AUTO, OFF, A. FLK, 1/160, . . . , 1/90 000 4 Operation SET PRESET PAN/TILT SET SHUTTER PRESET SET POSITION SAVE RETURN GOTO PRESET PRESET TOUR CLEAR PRESET CLEAR ALL FREEZE RETURN ON/OFF 0 to 127 0 to 127 34 Operation SET GROUP GROUP TOUR RUN CLEAR RETURN RECORD PATTERN RUN RETURN SET AUTO PAN AUTO PAN RUN CLEAR RETURN MASK NUMBER SET MASK MASK STATE PRIVACY MASK MASK COLOR WIDTH HEIGHT RETURN PROPORTIONAL PT COMPASS 1 to 9 1 to 9 1 to 9 1 to 4 1 to 4 1 to 8 1 to 8 ON/OFF GRAY, WHITE, BLACK 2 to 320 3 to 240 ON/OFF SET/ON/OFF SET GO DWELL TIME(0 to 100) RETURN OFF RETURN TIME (1 MIN to 100 MIN) 4 Operation HOME POSITION ON SPECIAL AUTO RETURN TILT LIMIT ON OFF ON/OFF PROTOCOL LG MULTIX/ PELCO D/ PELCO P 2 400/ 4 800/ 19 200/ 38 400/ 9 600 BPS COMMUNICATION BAUDRATE SAVE & EXIT RETURN Operation 35 RETURN USER TITLE ZOOM MAG OSD SET FUNCTION DOME ID RETURN LANGUAGE The option depends on the model. NORMAL ALARM IN1 to ALARM IN4 ALARM SET ON ALARM IN1 to ALARM IN4 DWELL TIME RETURN OFF ALARM OUT1 to ALARM OUT2 ALARM OUT1 to ALARM OUT2 ON OFF INFORMATION RESET INITIALIZATION FACTORY RESET RETURN RETURN DWELL TIME RETURN ALARM IN1 to ALARM IN4 3 to 255 OPEN/CLOSE PRESET 0 to 127 3 to 255 ON/OFF ON/OFF ON/OFF ON/OFF 4 Operation 36 Operation Please Enter Camera ID Target CAM ID : _ 2. Enter the connected camera ID to control the camera connected to the LKD1000 controller directly and then press ENTER. The camera control menu will be displayed. Menu navigation We use the LKD1000 controller in this manual to explain the features of the LG Dome camera because of the LKD1000's ability to control all of the LG Dome camera's advanced features. (For detailed controller instructions, refer to the LKD1000 Controller Manual. ) LKD1000 button Cam OSD button ZOOM IN button ZOOM OUT button Camera OSD operation Displays or removes the setup menu. Use to move upper direction on the menu screen. Use to move lower direction on the menu screen. MANUAL: Use [Near] or [Far] button to select the DC Iris level. DC Iris level are set by one parameter unit. · AGC (Automatic Gain Control) setting If the images are too dark, change the maximum [AGC] value to make the images bright. Select [AGC] option on the [EXPOSURE] menu. Use [Near] or [Far] button to select a mode. · 38 Operation WDR/BLC setting Use WDR/BLC option to set the options for BLC or WDR camera. Select [WDR/BLC] option on the [EXPOSURE] menu. Use [Near] or [Far] button to select a mode then press [Open] or [Close]. · WDR LEVEL: WDR (Wide dynamic range) feature can be very helpful to cope with very challenging lighting conditions. It is capable of capturing both of the dark part and bright part and combining the differences into a scene to generate a highly realistic image as original scene. BLC LEVEL: Camera's backlight compensation feature helps alleviate issues of visibility in high contrast areas. HSBLC: Use for masking brightness of the specific area to view the subject more clearly. · HSBLC LEVEL: Select the HSBLC level. [. . . ] A (Blank): Insert a space at the cursor position. Operation 47 DOME ID setting Displays or removes the Camera ID OSD on the screen. ALARM Setting This camera has a terminal that can sense the alarm signals. The camera can be programmed to go to a preset with a signal from any connected alarm device. 1. Select [DOME ID] option on the [OSD] menu. Use [Near] or [Far] button to set it [ON] or [OFF] 3. [. . . ]