User manual LG LTM9000W

[. . . ] Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces or shall be provided with brushings. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. FCC WARNING : This equipment may generate or use radio frequency energy. [. . . ] · The Alarm In 1 is Preset 1, Alarm In 2 is Preset 2, Alarm In 3 is Preset 3 and Alarm In 4 is Preset 4. Auto mode: Change the observe position to a sensor that senses a touch or shock then return to the position that previously observed. (Set the Duration Time of Alarm Input function to "1 to 255". ) Connecting LKD1000 controller Connecting the LKD1000 controller to control the camera. (Refer to the manuals of the LKD1000 controller for more details. ). Data Port Adapter <Example : If this unit receives signal from "Alarm 4"> Before inputting the alarm signal Alarm signal input Preset 1 Preset 4 Connections Alarm 4 Released alarm signal Preset 2 Alarm 1 Preset 3 LKD1000 controller Alarm 3 Alarm 2 Function status While observe a specific position. While operating Auto Pan function. Auto mode Change the observe position to the alarmed position then return to the position that previously observed. Stop preset touring and change the observe position to the alarmed position then restart the preset touring again. Stop auto panning and change the observe position to the alarmed position then restart the auto panning again. 17 TX- TX+ Connection of the data port and adapter with LKD1000 controller No 4 5 Description TRX D TRX D + Color Orange Yellow System Connection Note: When any peripheral is turned off and turned on again, the camera is also turned off and turned back on. Caution: Do not connect the alarm connectors to the another camera's alarm connectors. No 4 5 Description TRX D TRX D + Color Green Red Controller or TX- TX+ TX- TX+ Caution: Connect the supplied termination adapter to the final camera's data port to prevent the RS-485 communication error. 18 Operation Setup Menu Overview The following table shows the list of menu items and options. You can adapt the camera to your requirements by setting up the respective items in these menus. Main Menu Sub Menu FOCUS MODE FOCUS DIST ZOOM START ZOOM END ZOOM SPEED ZTRK MODE INITIAL SET EXIT IRIS AGC WDR/BLC BRIGHTNESS EXPOSURE SHUTTER SENS-UP INITIAL SET EXIT ATW AUTO ONE PUSH COLOR TEMP MANUAL INDOOR, OUTDOOR Contents AUTO/ ONE PUSH/ ZOOM TRIG/ MANUAL 50cm, 1m, 3m, 5m x1~x26 x2~x324 SLOW/ MIDDLE/ QUICK AUTO/ MANUAL/ AUTO ONLY RET/TOP/END AUTO/MANUAL OFF/LOW/MIDDLE/HIGH OFF/WDR/BLC/HSBLC 0~100 X512, ~, x2, AUTO, OFF, A. FLK, 1/160, ~, 1/90000 OFF, AUTO x2 ~ AUTO x128 RET/TOP/END Main Menu Sub Menu Contents LOW/ MIDDLE/ HIGH 5, 10, 15, DWELL TIME 30, 60 sec INITIAL SET RET/TOP/ EXIT END D/N LEVEL AUTO DAY/NIGHT DAY NIGHT OFF ZONE ZONE1 ~ NUMBER ZONE4 ZONE STATE OFF, ON WIDTH HEIGHT MOVE X MOVE Y SENSITIVITY INITIAL SET RET/TOP/ EXIT END FOCUS MOTION DET ON OFF MASK NUMBER MASK STATE PRIVACY MASK MASK1 ~ MASK8 ON WHITE BALANCE RED -100 ~ 100 BLUE -100 ~ 100 INITIAL SET EXIT RET/TOP/ END OFF, ON BLACK, MASK GRAY, COLOR WHITE WIDTH HEIGHT MOVE X MOVE Y RESET MASK INITIAL SET RET/TOP/ EXIT END Operation 3D-DNR OFF LOW MIDDLE HIGH 19 Main Menu Sub Menu CAMERA ID D-EFFECT COLOR FREEZE SHARPNESS STABILIZER SPECIAL OSD RESET LANGUAGE INITIAL SET EXIT FACTORY RESET S/W VERSION REBOOT EXIT Contents 0~255 Not supported. OFF ON COLOR LEVEL OFF/ ON 0~68 OFF/ ON OFF USER TITLE ZOOM MAG ON FUNCTION CAMERA ID ENG or ENG/CHN RET/TOP/END Menu navigation We use the LKD1000 controller in this manual to explain the features of the LG Dome camera because of the LKD1000's ability to control all of the LG Dome camera's advanced features. (For detailed controller instructions, refer to the LKD1000 Controller Manual. ) Buttons Cam OSD button ZOOM IN button ZOOM OUT button FOCUS NEAR button Function Displays the setup menu or cancels operation of the setup menu. If the camera is received auto-focus command, the camera is activated Auto-focus mode and the focus is set automatically and then the focus mode is automatically changed to manual mode. ZOOM TRIG: The focus is activated manually. If you change the zoom, the focus is activated Automatically and then the focus mode is automatically changed to manual mode. MANUAL: Focus is activated only when the FOCUS (NEAR or FAR) keys on the controller is pressed. Operation At this point, you have access to the camera setup menu. · · 1 Focus Distance setting Zoom Speed setting Selects the minimum shooting distance for the focus. Select [FOCUS DISTANCE] option on the [FOCUS] menu, then select a focus distance value (50CM, 1M, 3M, 5M). Selects a zoom speed. Select [ZOOM SPEED] option on the [FOCUS] menu, then select a zoom speed (SLOW, MIDDLE or QUICK). Zoom Start setting Zoom Tracking Mode setting You can set the zoom start position of the camera. When the zoom function is operated, the zoom always will start at the selected zoom start position. Select [ZOOM START] option on the [FOCUS] menu, then set a zoom start position (x1 - x26). Selects a zoom tracking mode. Zoom tracking means focused zooming state. [. . . ] The Function On-Screen Display of this camera can be turned on or off. Select [OSD] option on the [SPECIAL] menu. Use [Near] or [Far] button to select a [ON] and press [Open] or [Close]. The OSD menu appears. Freeze setting 1. [. . . ]