User manual LG LVC-D204HP

[. . . ] The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet Refer servicing to qualified personnel only. [. . . ] Moisture can damage the camera and also create the danger of electric shock. Do not expose the camera in such conditions as shown below. Use in a room or area filled with cigarette smoke, dust or gas. 2 What's in the box Video Cable M4 Tapping Screws (2EA) (Pan Lock Screw) Camera Body Optional Adapter (DC 12V, 300mA) 3 Construction Front View LG logo 4-pin Dip Switch Tilt Base Focus Lock Screw Side View Dome Cover Lens Tilting Lock Screw Dome Cover Separatory Spring 4 Construction Rear View Dome Cover Separatory Spring Power In Video Out N. C (Option: Ext. or Audio) GND Pan Base Base Fixing Hole 5 Installation Video Cable Connection RED Cable BLACK Cable WHITE Cable 1. BLACK : Connect the BLACK Cable to 2(-). WHITE : Connect the WHITE Cable to 3(V). 6 Installation Camera Installation 1. Aim the LG logo of the Dome Camera to face the place that you wish to watch. Tighten the M4 Tapping Screws to fix the Dome Camera on the ceiling, then adjust the Pan (Left / Right) by moving the Pan Base. Tighten the M4 Tapping Screws after adjustment. Adjust the Tilt (Up / Down) by moving the Tilt Base then tighten Tilting Lock Screw. Adjust the Focus by moving the Focus Lens then tighten Focus Lock Screw. Install the Dome Cover to the main body by turning it counterclockwise to the end. Pan Base Hole for Fixing Tilting Lock Screw Tilt Base M4 Tapping Screw Focus Lock Screw Dome Cover 7 Installation NOTE · When you disassemble the Dome Cover, lift the Dome Cover Separatory Spring on the opposite side of LG Logo and turn the Dome Cover clockwise simultaneously. Dome Cover Separatory Spring · · When you install the camera, handle with care. The camera could be damaged by improper handling or storage. If this camera is mounted on the other places except ceiling, you need an extra bracket for mounting. (not supplied) 8 Installation Camera Connection Connect the Power Adapter (12V, 300mA; optional) to the Power Input Jack of the camera as shown below. Power Input Jack Adapter Jack BNC Adapter Rear Panel Monitor 9 Setup 4-pin Dip Switch Setting This camera has the 4-pin Dip Switch inside of the camera for setting. ABL : Auto BLC The default setting is OFF. BLC : Backlight Compensation The default setting is OFF. [. . . ] You can set the background compensation to OFF. · · 12 Dimension ø100 76. 5mm 26. 5mm ø120 ø 90 13 Specifications (1) Signal System Total / Effective Pixels Pick-Up Device Lens Angular Field of View (D) Focus Signal Process Scanning System Sync. System Scanning Frequency Model NTSC PAL 410K/380K 470K/440K 1/3-Inch Interline Color CCD (Super HAD) Fixed Lens (f=3. 0mm/F=2. 0, f=3. 7mm/F=2. 0 * 1) / f=6. 0mm/F=1. 8, f=8mm/F=2. 5, f=12mm/F=2. 5) 115°(f=3. 0mm), 92°(f=3. 7mm), 54°(f=6mm), 38. 6°(f=8mm), 25. 7°(f=12mm) Manual Digital Signal Process 2 : 1 Interlace Internal LVC-D200HM LVC-D200HP Resolution S/N Ratio Standard Illuminance Sensitivity (1/3 output) Video Output Signal Gain Control Shutter Speed White Balance Back Light Power Source Power Consumption Operating Temp. Weight Dimensions 59. 94 Hz(VD) 50Hz(VD) 480 Line (H) 470 Line (H) More than 48dB 2000Lux (3200° K) 0. 5 Lux (F1. 2) 1Vp-p Composite (75) Auto Electronic Shutter Electronic Shutter (1/60 ~ 1/10000) (1/50 ~ 1/10000) Auto Compensation ON/OFF, AUTO DC12V 2. 3W -10°C ~ 50°C (Humidity : 0%RH ~ 60RH) -20°C ~ 60°C (Humidity : 0%RH ~ 85RH) 182g ø120 (Diameter)x76. 5(H), Dome Size=ø100 *1) LVC-D200'S (3mm) / LVC-D201'S (6mm) / LVC-D202'S (12mm) LVC-D203'S (8mm) / LVC-D204'S (3. 7mm) Design and specifications are subject to change without notice. 14 Specifications (2) Signal System Total / Effective Pixels Pick-Up Device Lens Angular Field of View(D) Focus Signal Process Scanning System Sync. [. . . ]