User manual LG LVC-SX810HM

[. . . ] Replaced only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. · Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces or shall be provided with brushings. Warning: Do not install this equipment in a confined space such as a bookcase or similar unit. [. . . ] Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power- supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/accessories specified by the manufacturer. 4 LVC-SX810HM_HP_ENG_77T 6/13/07 3:41 PM Page 5 Contents and Features Contents Part Names and Functions . . 18-19 Features This color video camera is designed for use in monitoring system. · High resolution and high sensitivity with a 1/3 inch Super HAD CCD (Charge Coupled Device) · CS Mount (Adapter Ring Mount for C Lens: Optional) · The input power source is DC 12V (4. 5W (Max)). Maintenance of the unit · Remove dust or dirt on the surface of the lens with a blower. · Use a dry soft cloth to clean the body. If it is very dirty, use a cloth dampended with a small quantity of neutral detergent and then wipe dry. · Avoid the use of volatile solvents such as thinners, alcohol, benzene, and insecticides. They may damage the surface of the body. 5 LVC-SX810HM_HP_ENG_77T 6/13/07 3:41 PM Page 6 Part Names and Functions 1. Camera mounting bracket The bracket can be fixed at the top or bottom of the camera. Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). Flange-back adjustment dial 6 LVC-SX810HM_HP_ENG_77T 6/13/07 3:41 PM Page 7 Part Names and Functions 7. Video output connector (BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. Function switches for manual setting To set functions, use these dip switches. Lens iris output connector (LENS) This 4- pin connector is used to send the Iris control signal and power supply to an auto-iris type lens. ALC Lens Setting Switch DC: When you attach an Auto Iris lens requiring the DC control signal, please put this switch in the DC position. ELC: When you attach a manual or fixed lens, please put this switch in the ELC position. VIDEO: When you attach an Auto Iris lens requiring the video control signal, please put this switch in the VIDEO position. [. . . ] · Depending on the type of lens used, the lens may not perform properly. In such a case, adjust the LEVEL volume on the lens casing to correct. ALC volume level control VEL ALC LE LEVEL volume level control 12 LVC-SX810HM_HP_ENG_77T 6/13/07 3:41 PM Page 13 Function Switch Settings No 1 Name White Balance Position AWB HOLD 2 AGC (Auto Gain Control) ON OFF 3 BLC (Back Light Compensation) FL (Flickerless) ON OFF ON OFF 5 D&N (Day & Night) D&N AUTO D&N MAN Function Effect Auto tracking White Balance White Balance Hold AGC level varies from 10dB to maximum 30dB 10dB (Max. ) Sets to this position when strong light comes in behind the target Normal position Shutter speed is fixed. When changing the position of the camera mounting bracket, you should always reuse the screws that have been removed. Notes: · If using a camera mounting bracket, select a location that is strong enough to bear the full weight of the camera and the mounting bracket for long periods, and install the camera and mounting bracket securely. [. . . ]