User manual LG LW7000ER

[. . . ] website http://www. lgservice. com LG ENGLISH LG Window-Type Air Conditioner OWNER'S MANUAL MODELS, MODELOS: WK Series: LW7000ER LW8000ER WL Series: L1004R LW1000ER L1204R LW1200ER L1404R LB1000ER LB1200ER WP Series: LW1400ER L1504R LW1500ER L1804R LW1800ER ESPAÑOL IMPORTANT Please read through this manual. It contains valuable information about your air conditioner. This manual may help save time and money by explaining proper air conditioner maintenance and preventing improper use. PRECAUTIONS Pay close attention to precautions in order to prevent potential hazards and damage from misuse or improper installation. LG is not responsible for any damages caused by misuse of the air conditioner. Window-Type Air Conditioner Owner's Manual TABLE OF CONTENTS FOR YOUR RECORDS Write the model and serial numbers here: Model # Serial # You can find them on a label on the side of each unit. [. . . ] Restriction of outside air will greatly reduce the cooling efficiency of the air conditioner. 30"~60" About 1/2" Over 20" CAUTION: All side louvers of the cabinet must remain exposed to the outside of the structure. 4 Install the unit a little slanted so the back is slightly lower than the front (about 1/2"). This will force condensed water to flow to the outside. 5 Install the unit with the bottom about 30"~60" above the floor level. Window Requirements NOTICE : All supporting parts should be secured to firm wood, masonry, or metal. · This unit is designed for installation in standard double hung windows with actual opening widths from 27" to 39". · The top and bottom window sash must open sufficiently to allow a clear vertical opening of 16" from the bottom of the upper sash to the window stool. 27" to 39" 16" min (With frame curtain) Stool Offset 1 /2" to 11/4" Sill Interior wall 23 5/8" min. (Without frame curtain) Exterior 15 WP Series How to Install the Unit 1 To prevent vibration and noise, make sure the unit is installed securely and firmly. Fence Awning Cooled air Heat radiation 2 Install the unit where the sunlight does not shine directly on the unit. 3 There should be no obstacles, such as a fence and wall, within 20" from the back of the cabinet because it will prevent heat radiation of the condenser. Restriction of outside air will greatly reduce the cooling efficiency of the air conditioner. 30"~60" About 1/2" Over 20" CAUTION: All side louvers of the cabinet must remain exposed to the outside of the structure. 4 Install the unit a little slanted so the back is slightly lower than the front (about 1/2"). This will force condensed water to flow to the outside. 5 Install the unit with the bottom about 30"~60" above the floor level. Window Requirements NOTICE : All supporting parts should be secured to firm wood, masonry, or metal. · This unit is designed for installation in standard double hung windows with actual opening widths from 29" to 41". · The top and bottom window sash must open sufficiently to allow a clear vertical opening of 18" from the bottom of the upper sash to the window stool. Sash 29" to 41" 18" min. Inner sill Window Offset Sill Exterior Interior wall 29" min. (Without frame curtain) 16 WK, WL Series ENGLISH Installation Kits Contents 1 2 3 4 5 6 7 8 13 10 12 9 11 NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 NAME OF PARTS FRAME CURTAIN SILL SUPPORT BOLT NUT SCREW (TYPE A) SCREW (TYPE B) SCREW (TYPE C) FOAM-STRIP DRAIN PIPE FOAM-PE FRAME GUIDE WINDOW LOCKING BRACKET FOAM-PE Q'TY 2 2 2 2 16 3 5 1 1 1 2 1 1 Suggested Tool Requirements SCREWDRIVER(Philips and Flatead), RULER, KNIFE, HAMMER, PENCIL, LEVEL PREPARATION OF CHASSIS 1 Remove the screws which fasten the cabinet at both sides and at the back. Shipping Screws 2 Slide the unit from the cabinet by gripping the base pan handle and pulling forward while bracing the cabinet. 3 Cut the window sash seal to the proper length. Peel off the backing and attach the Foam-PE underside of the window sash. to the 4 Remove the backing from the top upper guide Foam-PE and attach it to the bottom of the Upper Guide. 5 Attach the upper guide onto the top of the cabinet with 3 Type A screws . Upper guide 6 Insert the Frame Guides cabinet. into the bottom of the 13 7 Insert the Frame Curtain Frame Guides A screws . . into the Upper Guide and (Type A) 5 10 Upper guide 11 8 Fasten the curtains to the unit with 4 Type 5 11 5 (Type A) 17 Cabinet Installation 1 Open the window. Mark a line on center of the window stool. Carefully place the cabinet on the window stool and align the center mark on the bottom front with the center line marked in the window stool. Upper Guide Window stool Front Angle Fig. 1 Upper guide 2 Pull the bottom window sash down behind the Upper Guide until it meets. NOTICE Window Sash : Do not pull the window sash down tightly that the movement of Frame Curtain is restricted. Foam-pe 13 Cabinet Frame Curtain 1 Foam-pe 10 Fig. 2 3 Loosely assemble the Sill Support in Fig. using the parts INDOOR OUTDOOR Sill Support Bolt 3 2 Nut 4 Fig. 3 4 Select the position that will place the Sill Support near the outer most point on sill (See Fig. 4) NOTICE Screw(Type A) Frame Guide 11 5 : Be careful when you install the cabinet are broken easily). (Frame Guides Cabinet INDOOR OUTDOOR 5 Attach the Sill Support to the cabinet track hole in relation to the selected position using 2 Type A screws in each support (See Fig. 4 18 About 1/2" ENGLISH 6 The cabinet should be installed with a very slight tilt (about 1/2") downward toward the outside (See Fig. Adjust the bolt and the nut of Sill Support balancing the cabinet. for Screw(Type B) 6 7 Attach the cabinet to the window stool by driving (Type B: Length 16mm (5/8 inch) the screws and below. ) through the front angle into window stool. Sill Support 2 Sash track 8 Pull each Frame Curtain fully to each window sash track, and repeat step 2. Front Angle Screw(Type B) Sill Support 2 6 9 Attach each Frame Curtain screws the window sash using (Type C). [. . . ] : DO NOT USE AN EXTENSION CORD on 230, 208, and 230/208 Volt units. PREFERRED METHOD NOTICE 3-prong grounding plug 3-prong grounding type wall receptacle Ground prong Power supply cord Ensure proper ground exists before use Fig. 24 DO NOT CUT OR REMOVE THE THIRD (GROUND) PRONG FROM THE POWER PLUG. FUSE ­ Use a time-delay fuse or circuit breaker. Refer to serial plate for proper power supply requirements. 26 Common Issues Common Problems and Solutions ENGLISH Before calling for service, please review the following list of common problems and solutions. [. . . ]