User manual LG LWC051JGMK1

[. . . ] CONSTRUCTION VIEWS (EXTERNAL VIEWS) . . . . . . . . . . . . . . . . . . . . . . . . WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PARTS RATING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . REFRIGERATING CYCLE DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 2) Setting contents · In case of AI-NET central control Operation from AI-NET central control [After-push priority] [Center] [Operation prohibited] (¡: Operation possible Operation on RBC-AMT32E ON/OFF setting Operation selection Timer setting Temp. setting Air speed setting Air direction setting On RBC-AMT32E ¡ × × × ¡ ¡ ¡ × × × ¡ ¡ ¡ ¡ ¡ ¡ × × × [Center controlling] display : Operation impossible) · In case of wired remote controller type, [Central control] display (Goes on) in the central control mode · Display flashes when an item of the operation prohibited was changed on the remote controller. · In case of wireless remote controller type, the display lamp does not change but the contents that can be operated are same in the central control mode. (1) The operation from the wireless remote controller in the central control mode is notified with the receiving sound, Pi, Pi, Pi, Pi, Pi (5 times). (1) If the operation select modes are different in the central 2 to 4 from those at the central controller side, the operations Temp. Setting, air volume setting, and air direction setting are inoperable. · In case of TCC-LINK central control Operation from TCC-LINK central control Individual [Central 1] [Central 2] [Central 3] [Central 4] (¡: Operation possible Operation on RBC-AMT32E ON/OFF setting Operation selection Timer setting Temp. setting Air speed setting Air direction setting On RBC-AMT32E ¡ ¡ ¡ × × ¡ ¡ ¡ × × × × × ¡ ¡ ¡ ¡ ¡ × × ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ [Central control] display ×: Operation impossible) 58 No. 18 Item Louver control: In case of 4-way Discharge Cassette type Outline of specifications 1) Louver position setup · When the louver position is changed, the position moves necessarily to downward discharge position once to return to the set position. · The louver position can be set up in the following operation range. Remarks The louver position at horizontal discharge position at under AP030 differs from that at over AP036. In cooling/dry operation In heating/fan operation · In group twin/triple operation, the louver positions can be set up collectively or individually. In case that HEAT refrigerant recovery control was performed in STOP status, the louver position becomes horizontal when the operation is resumed. 2) Swing setup · [SWING] is displayed and the following display is repeated. In all operations The swinging louver moves usually up to the ceiling side from the louver position of the set time. (Repeats) · In group operation, the louver positions can be set up collectively or individually. · Three types of the swing modes can be also selected and set by the setup data of Item code (DN) [F0]. · In case of selecting the Swing mode, "Dual swing" or "Cycle swing", the following numerals is displayed at the center of the remote controller screen for approx. SWING/FIX button was pushed to select 3 seconds when [SWING]. (No display for the standard swing) Remarks On the remote controller before the wired remote controller (RBC-AMT32E), the mode cannot be moved to the select mode SWING/FIX even if pushing button for a long time. Carry out setting operation during stop of the unit; otherwise the unit stops operation. The standard swing performs the same swing operation as the present operation (2 series). For the setting operation, refer to [How to set up type of the swings] in Item "Setup at local site/ Others". On the remote controller before the wired remote controller (RBC-AMT32E), flashing showing the Swing mode is not indicated. Alternate lighting (0. 5 sec. ) Alternate lighting (0. 5 sec. ) Dual swing Cycle swing <<Louver lock (Louver fix)>> · For the air direction setup for each discharge port, the louver position can be locked during the normal operation. · An arbitrary air direction of an arbitrary louver can be registered and set by keeping UNIT LOUVER button pushed for 4 seconds or more on the remote controller. · The louver lock can be set by registering the setup data to Item code (DN) [F1] to [F4] according to the following table. Item code Objective louver No. F1 F2 F3 F4 01 02 03 04 Setup data 0000: Release (At shipment) 0001: Horizontal discharge position On the remote controller before the wired remote controller (RBC-AMT32E), UNIT LOUVER button is not provided. [. . . ] The Even after modifying the CL data wrongly and pushing button, it is possible to return to the data before modification by pushing button if the CODE No. (DN) is not changed. <Fig. 3 EEPROM layout diagram> The EEPROM (IC503) is attached to the IC socket. When detaching the EEPROM, use a tweezers, etc. Be sure to attach the EEPROM by fitting its direction as shown in the figure. [. . . ]