User manual LG LWC1260BCG

[. . . ] WIRING DIAGRAM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPECIFICATIONS OF ELECTRICAL PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . REFRIGERANT CYCLE DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CONTROL BLOCK DIAGRAM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · A place where the operation noise and discharged air do not disturb your neighbors. 3 Specifications x 3 * To reset to [A] setting, push the [MODE] button again while pushing the [CHK] button. 4 Drain nipple x 1 (Heat pump model only) · A place which is not exposed to a strong wind. · A place which does not block a passage. · When the outdoor unit is to be installed in an elevated position, be sure to secure its feet. · There must be sufficient spaces for carrying the unit into and out of the site. · A place where the drain water does not raise any problem. 3. Confirm the indoor unit can operate with the changed setting of the remote control. Required tools for installation work 1) Philips screw driver 2) Hole core drill (65 mm) 3) Spanner ­ 45 ­ MODE TEMP . AUTO COOL DRY FAN ONLY FAN AUTO Hr. ON OFF TIMER B C LOW MED. HIGH B C TEMPORARY button TEMPORARY 4) Pipe cutter 5) Knife 6) Reamer 7) Gas leak detector 8) Tape measure 9) Thermometer 10) Mega-tester 11) Electro circuit tester 12) Hexagonal wrench (5 mm) 13) Flare tool 14) Pipe bender 15) Level vial 16) Metal saw CAUTION 1. Install the outdoor unit without anything blocking the air discharging. When the outdoor unit is installed in a place exposed always to a strong wind like a coast or on a high story of a building, secure the normal fan operation using a duct or a wind shield. Specially in windy area, install the unit to prevent the admission of wind. TEMP. START/STOP SET FAN ECONO. Fig. Operate the unit at cooling operation mode for 15 minutes or more. Insert a flare nut into the pipe, and flare the pipe. As the flaring sizes of R410A differ from those of refrigerant R22, the flare tools newly manufactured for R410A are recommended. However, the B conventional tools can be used by adjusting projection margin of the copper pipe. 9-3-3 mo 100 re mm fro m wor all 600mm or more ­ 46 ­ 1. Tight connection (between pipes and unit) 3. Evacuate the air in the connecting pipes using VACUUM PUMP. (connected points) * In the case of flaring for R410A with the conventional flare tool, pull out it approx. 0, 5 mm more than that for R22 to adjust to the specified flare size. The copper pipe gauge is useful for adjusting projection margin size. 9-3-7 · Install the provided drain nipple in the hole of the bottom plate. · Perform proper drainage processing using a drain hose sold separately or one on the market. [. . . ] Otherwise it would cause insulation inferiority because of dew drops. 3) When replacing the sensor using the colored protective tube, wind the color tape matching the color of that tube. Remarks Thermal sensor part Cutting here Connector 100 200 Cutting here 15 70 Thermal constringent tube Cutting here 100 15 70 Soldered part Dryer Winding the color tape These are parts for servicing sensors. Please check that the accessories shown in the right table are packed. Parts name 1 2 3 4 5 6 Sensor Sensor Spring (A) Sensor Spring (B) Thermal constringent tube Color tape Terminal Q'ty 1 1 1 3 1 3 Remarks Length : 3m For spare For spare Including one spare 9 colors ­ 77 ­ MCC-758 ­ 78 ­ MCC-775 ­ 79 ­ 12. Indoor Unit (1) RAS-M10, M13YKV-E RAS-M10, M13YKCV-E 407 : RAS-M10YKCV-E 408 : RAS-M13YKCV-E 409 : LWC1260BCG 410 : RAS-M10YKV-E 404 402 412 403 413 405 Location No. [. . . ]