User manual LG LWC226NBMM7

[. . . ] · Do not use for other purposes such as preservation of food. · Do not use any combustible equipment in front of the airflow outlet. · Do not expose directly to cold air for a long period. · Ensure that the drainage pipe is connected properly. [. . . ] Note for the battery symbol (bottom two symbol examples): This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the Directive for the chemical involved. Pb · Do not switch ON the unit when waxing the floor. After waxing, aerate the room properly before operating the unit. · Do not install the unit in oily and smoky areas. 3 ENGLISH OPERATION CONDITION OPERATION CONDITION OPERATION CONDITION Use this air conditioner under the following temperature range (CU-E10HBEA, CU-E15HBEA, CU-E18HBEA, CU-E21HBEA) Temperature (°C) COOLING HEATING Maximum Minimum Maximum Minimum Indoor *DBT 32 16 30 16 *WBT 23 11 *DBT 43 -10 24 -10 Outdoor *WBT 26 18 - NOTICE: · This unit is still able to operate as a cooler with outdoor temperature as low as -10°C in a non-living room, such as a computer room, with a room temperature of 16°C or above, and room humidity up to 80%. When the outdoor temperature drops to -10°C, compressor will be cut off and resume operation again once the temperature rises to more than -10°C. · When the outdoor temperature is out of the above temperature range, the heating capacity will drop significantly and outdoor unit might stop for protection control. (CU-2E15GBE, CU-2E18CBPG, CU-3E18EBE, CU-3E23CBPG, CU-4E27CBPG) Temperature (°C) COOLING HEATING (CU-3E18JBE, CU-4E23JBE) Temperature (°C) COOLING HEATING * DBT: Dry bulb temperature * WBT: Wet bulb temperature Maximum Minimum Maximum Minimum Indoor *DBT 32 16 30 16 *WBT 23 11 *DBT 46 -10 24 -15 Outdoor *WBT 26 18 -16 Maximum Minimum Maximum Minimum Indoor *DBT 32 16 30 16 *WBT 23 11 *DBT 43 16 24 -10 Outdoor *WBT 26 11 18 -11 4 MULTI AIR CONDITIONER FUNCTION MULTI AIR CONDITIONER FUNCTION (CU-2E15GBE, CU-2E18CBPG, CU-3E18EBE, CU-3E18JBE, CU-3E23CBPG, CU-4E23JBE, CU-4E27CBPG) DEFINITION Multi air conditioner system has one outdoor unit connected to multiple indoor units. INDOOR UNIT · It is possible to operate the indoor units individually or simultaneously. · The operation mode priority is given to the first unit that turned on. · During operation, heating and cooling mode could not be activated at the same time for different indoor unit. · The power indicator blinks to indicate the indoor unit is standing by for different operation mode. Room C Room A Room D Room B Outdoor unit 5 ENGLISH PRODUCT OVERVIEW & OPERATIONS PRODUCT OVERVIEW & OPERATIONS Indoor Unit Remote Control Open the cover to use the buttons 13 14 15 OFF / ON 16 12 17 18 OFF / ON Remote Control Preparation 11 1 TIMER/CLOCK MODE UP 1 2 3 4 Press CLOCK Press or current day. Press SET UP DOWN to select SELECT FAN SPEED MODE 4 TEMP RC 2 5 3 to confirm. 7 OFF/ON DOWN SET QUIET/ AIR SWING POWERFUL CLOCK CANCEL CHECK AC 6 RESET Repeat steps 2 and 3 to set the current time. 8 1 2 3 4 5 6 6 Operation LED OFF/ON Button Temperature Setting Button Operation Mode Button Fan Speed Button Quiet/Powerful Operation Button 9 13 14 15 16 17 18 10 Timer/Clock Setting Display Fan Speed Display Temperature Setting Display Quiet Operation Indicator Powerful Operation Indicator System Error Display 7 8 9 10 11 12 Timer Setting Button Group Check Button Air Conditioner Reset Button Remote Control Reset Button OFF Indicator Operation Mode Selection Indicator · Please be aware of the OFF indication on the remote control display to prevent the unit from starting/stopping improperly. Press Timer for 4 seconds to change display to weekly timer. MODE 2. Press press SELECT to enter day setting. UP 3. Press Timer SELECT or or until your desired day is shown, to check the set programs. to confirm your selection. UP DOWN 4. Press Timer Modify Current Timer Program or Add New Timer Program 1. Press SELECT MODE to enter timer mode. DOWN to enter day setting. UP 3. Press Timer or until your desired day is shown. 4. Perform steps 4 to 7 of "Day and Timer Set Up Method" to modify existing timer program, or add any timer program. Cancel Current Timer Program Perform the step below to cancel the timer program for a particular day. Press SELECT to enter day. UP 2. Press SELECT UP or or DOWN until your desired day is shown. will disappear. or DOWN to select your desired day. SELECT 3. · Power cord becomes unnaturally warm. [. . . ] When abnormality occurs, use remote control to retrieve error code. Ensure the operation LED is in OFF condition. OFF Indicator Operation LED OFF / ON 2 Press or . If error code and abnormality can be identified, the operation LED will be ON continuously, then jot down the error code. UP DOWN TIMER/CLOCK MODE UP SELECT FAN SPEED MODE 1 TEMP Press for 5 seconds. OFF/ON DOWN SET QUIET/ AIR SWING POWERFUL CLOCK CANCEL CHECK AC RESET RC 3 Press for 5 seconds to quit checking. 4 10 Reveal the error code to authorized dealer. MEMO 11 ENGLISH QUICK GUIDE/GUIDE RAPIDE/GUÍA RÁPIDA/ KURZANLEITUNG/GUIDA RAPIDA/SNELLE GIDS/GUIA RÁPIDO/ / 1 OFF / ON OFF / ON 2 MODE TIMER/CLOCK MODE UP SELECT FAN SPEED MODE OFF/ON DOWN SET QUIET/ AIR SWING POWERFUL TEMP CLOCK CANCEL CHECK AC RESET RC AUTO DRY HEAT COOL 3 TEMP Start/stop the operation. [. . . ]