User manual LG LWG07

[. . . ] Never spill any kind of liquid into the unit. Should this happen, unplug or main switch off the unit and contact an authorized service center. Do not insert anything between the air outlet blades because the inner fan may be damaged and could cause injury. Do not place any obstacles in front of the unit. [. . . ] or Press the on the unit until the indicator lights up Each time you press a button, the unit beeps. 4 To set the fan speed to. . . High Med Low Result: 5 E-8 To control the direction of the air flow, refer to page . DB98-22420A-1. indd 8 2006-5-31 16:31:29 Heating Your Room Remote Control Control Panel ENGLISH 16:31:30 You must select the Heat mode if you wish to heat your room to a specific temperature. You can also set the fan speed. If necessary, press the Result: (On/Off) button. The operating mode indicator (COOL, FAN or HEAT) on the unit comes on. The air conditioner starts up in the mode selected when the unit was last used. The unit beeps twice. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: Plugged in Stopped It will start up aotomatically after about three minutes. If the HEAT indicator is not lit up on the unit: Press the button on the remote control or Press the MODE button on the unit one or more times until the HEAT indicator lights up Result: The unit beeps each time you press MODE. The air conditioner starts up in Heat mode. You can change modes at any time. 3 To adjust the temperature, press the To adjust the temperature, press the or or button on the remote button on the unit one control one or more times until the required temperature is displayed. or more times until the required temperature is displayed. Possible temperatures are between 8°C and 30°C inclusive. Result: Each time you press the temperaure buttons. - The temperature is adjusted by °C and displayed on the control panel - The unit beeps The air conditioner starts cooling if the room temperature is higher than the selected temperature. Press the button on the remote control. The air conditioner switches off automatically when the operating time reaches zero. You can change the fan speed and air flow direction and others after setting the Off Timer. To Cancel the Off Timer To cancel the Off Timer, press: Timer on the remote control or unit one or more times until " displayed. or on the remote control or unit (The air conditioner operates in the mode selected when the unit was last used. ) " is E-3 DB98-22420A-1. indd 13 2006-5-31 16:31:34 Setting the Sleep Timer The Sleep Timer can be used when you are cooling or heating your room to switch the air conditioner off automatically after a period of 8 hours. If you wish to switch the unit off at a specific time, refer to page 3. Make sure that you have selected either COOL or HEAT mode. Remote Control Control Panel Press the or Press the Result: button on the remote control button on the unit until the SLEEP indicator lights up. Each time you press a butoon, the unit beeps. The "SLEEP" passes through the control panel for about 5 seconds and the" "will be dispalyed. The remaining time is displayed and decreased by hour automatically to indicate the remaining time. The air conditioner will be controlled as illustration below. Cooling When the temperature has been increased by °C(after hour), it is maintained for 7 hours. Set TEMP. 1hr 8hr Start time Stop time Heating The temperature is decreased by °C after hour. When it has been decreased by °C (after hour), the temperature is maintained for 6 hours. To Cancel the Sleep Timer To cancel the timer, press: on the remote control. The SLEEP indicator is no longer displyed. The air conditioner operates in the mode selected last. E-4 DB98-22420A-1. indd 14 2006-5-31 16:31:35 Operating Recommendations ENGLISH E-5 2006-5-31 16:31:35 Here air a few recommendations that you should follow when using your air conditioner. Topic Heating performances Recommendation The heat pump inside the air conditioner absorbs heat from outside air and brings it indoors. If the temperature of the outside air drops, the air conditioner will heat less. [. . . ] When heating, the required room temperature is never reached and the air conditioner frequently stops Check that the required temperature has been set correctly. If the air flow is directed downwards, direct it upwards. Check that the air conditioner has been switched on;if necessary, press The air flow direction does not change when you press AIR SWING (On/Off) on the remote control or unit. The timer is not correctly triggered Check that the timer has been programmed correctly; see page ~4. Odours are permeated in the room during air conditioning Air the room. E-8 DB98-22420A-1. indd 18 2006-5-31 16:31:37 Installation ENGLISH 300mm 500mm Before installation, be sure to check the installation area or the air conditioner, and drain hose. Checkpoints prior to installation Check the cabinet and front grille of the unit for any harmful defects such as scratches. [. . . ]