User manual LG M1921A-BT

[. . . ] The power supply cord is used as the main disconnection device. Ensure that the socket-outlet is easily accessible after installation. Operate the display only from a power source indicated in the specifications of this manual or listed on the display. If you are not sure what type of power supply you have in your home, consult with your dealer. [. . . ] Disposal of this product must be carried out in accordance to the regulations of your local authority. A2 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand 1. Place the monitor with its front facing downward on a soft cloth. Assemble the Stand Base(Front, Rear) into the Stand Body in the correct direction. Stand Body Stand Base 3. Tie down the base lock to perpendicularity direction. 4. Once assembled take the monitor up carefully and face the front side Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. A3 Connecting the Display Disassembling the stand 1. Put a cushion or soft cloth on a flat surface. 2. Place the monitor face down on the cushion or soft cloth. 3. Change your lock on the product as it follows and turn it in the arrow direction. If you can't release the stand base even the locking rib is at a release position, Please push the indicated rib down and retry it. 4. Pull out the stand to remove. A4 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range: -5°~15° -5 15 Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. A5 Connecting the Display Using the Computer 1. Make sure to turn off the computer and product. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making image adjustments. To make adjustments in the On Screen Display, follow these steps: Press the MENU Button, then the main menu of the OSD appears. To access a control, use the or Buttons. When the icon you want becomes highlighted, press the AUTO/SET Button. Use the / Buttons to adjust the image to the desired level. Use the AUTO/SET Button to select other sub-menu items. Push the MENU Button once to return to the main menu to select another function. Push the MENU Button twice to exit from the OSD. A10 On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu CINEMA MODE AUTO BRIGHT TIME CONTROL LIVE SENSOR SMART EZ ZOOMING 4:3 IN WIDE NORMAL Sub-menu A Reference To focus on the moving picture selected To control screen brightness automatically To mind user using time To control touch key distance To control smart key menu To adjust the resolution To adjust the image size PHOTO EFFECT GAUSSIAN BLUR SEPIA MONOCHROME BRIGHTNESS CONTRAST GAMMA sRGB PRESET 6500K 9300K To adjust screen color mode PICTURE To adjust the brightness, contrast and gamma of the screen COLOR RED GREEN BLUE HORIZONTAL VERTICAL To costomize the color of the screen To adjust the position of the screen TRACKING CLOCK PHASE SHARPNESS LANGUAGE HORIZONTAL OSD POSITION VERTICAL WHITE BALANCE POWER INDICATOR FACTORY RESET MOVIE INTERNET USER NORMAL DEMO To improve the clarity and stability of the screen SETUP To costomize the screen status for a user's operating environment FLATRON F-ENGINE To select or customize desired image settings : Adjustable A : Analog Input NOTE The order of icons may differ depending on the model (A11~A19 ). A11 On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears. Main Menu MENU : Exit : Adjust (Decrease/Increase) SET : Enter : Select another sub-menu : Restart to select sub-menu Button Tip Menu Name Icons Sub-menus NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual. A12 On Screen Display(OSD) Selection and Adjustment Main menu PICTURE Sub menu Description PICTURE BRIGHTNESS CONTRAST GAMMA To adjust the brightness of the screen. : -50/0/50 On the monitor, high gamma values display whitish images and low gamma values display high contrast images. MENU : Exit : Decrease : Increase SET : Select another sub-menu COLOR COLOR PRESET · sRGB: Set the screen color to fit the SRGB standard color specification. Set your own blue color levels. RED GREEN MENU : Exit : Decrease BLUE : Increase SET : Select another sub-menu A13 On Screen Display(OSD) Selection and Adjustment Main menu TRACKING Sub menu Description TRACKING HORIZONTAL VERTICAL To move image left and right. [. . . ] 'Specifications' section of this manual and configure your display again. G Do you see a "CHECK SIGNAL CABLE" message on the screen?· This message appears when the signal cable between your PC and your display is not connected. Check the signal cable and try again. Do you see a "OSD LOCKED" message on the screen? G Do you see "OSD LOCKED" when you push MENU button? [. . . ]