User manual LG M2094D

[. . . ] OWNER'S MANUAL M1994D M2094D M2294D Please read this manual carefully before operating your set. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service. Trade Mark of the DVB Digital Video Broadcasting Project (1991 to 1996) I D N u m b e r ( s ) : 5573 : M1994D 5574 : M2094D 5575 : M2294D PREPARATION FRONT PANEL CONTROLS I This is a simplified representation of the front panel. The image shown may be somewhat different from your set. A Type B Type INPUT Button MENU Button OK Button VOLUME Buttons INPUT Button MENU Button OK Button VOLUME Buttons INPUT INPUT MENU OK VOL PR MENU OK VOL PROGRAMME Buttons PROGRAMME Buttons PR Power Button Power Button Headphone Button Headphone Button 1 PREPARATION BACK PANEL INFORMATION I This is a simplified representation of the back panel. [. . . ] "Dolby "and the double-D symbol are trademarks of Dolby Laboratories. · There is a possibility that when HDMI mode, some DVD players do not make SPDIF sound. At that time, set the output of the digital audio of the DVD player to PCM. · Press the MENU or EXIT button to close the menu window. · Press the BACK button to move to the previous menu screen. 57 SOUND &LANGUAGE CONTROL TV SPEAKERS ON/ OFF SETUP You can adjust the internal speaker status. In COMPONENT the TV speaker can be operational even when there is no video signal. If you wish to use an external Hi-Fi system, turn off the TV internal speakers. AUDIO D Move OK + + + + + AUDIO D Move OK + + + + + · 500Hz · 1. 2KHz · 3KHz · 7. 5KHz · 12KHz · Reset Digital Audio Out : PCM TV Speaker On TV Speaker :: Off 0 0 0 0 0 - · 500Hz · 1. 2KHz · 3KHz · 7. 5KHz · 12KHz · Reset Digital Audio Out : PCM TV Speaker On TV Speaker :: Off 0 0 0 0 0 - Off On On 1MENU 2 OK Select AUDIO. Select TV Speaker. 3 OK Select On or Off. · Press the MENU or EXIT button to close the menu window. · Press the BACK button to move to the previous menu screen. 58 SOUND &LANGUAGE CONTROL AUDIO RESET Settings of the selected Sound Mode return to the default factory settings. AUDIO D Move OK + + + + + + + AUDIO D Move OK · 120Hz · 200Hz · 500Hz · 1. 2KHz · 3KHz · 7. 5KHz · 12KHz Reset ·· Reset 0 0 0 0 0 0 0 - + · 120Hz 0+ · 200Hz 0+ · 500Hz 0· 1. 2KHz 0 i Resetting sound mode configuration. . . · 3KHz 0 + · 7. 5KHz 0+ · 12KHz 0· Reset Reset · 1MENU 2 OK Select AUDIO. Select Reset. 3 OK Initialize the adjusted value. · Press the MENU or EXIT button to close the menu window. · Press the BACK button to move to the previous menu screen. 59 SOUND &LANGUAGE CONTROL I/II Stereo/Dual Reception (In Analogue Mode Only) When a programme is selected, the sound information for the station appears after the programme number and station name disappear. I/II Select the sound output. Broadcast Mono Stereo Dual On Screen Display MONO STEREO DUAL I, DUAL II, DUAL I+II A Mono sound selection If the stereo signal is weak in stereo reception, you can switch to mono. In mono reception, the clarity of sound is improved. Language selection for dual language broadcast If a programme can be received in two languages (dual language), you can switch to DUAL I, DUAL II or DUAL I+II. DUAL I DUAL II DUAL I+II A Sends the primary broadcast language to the loudspeakers. Sends the secondary broadcast language to the loudspeakers. Sends a separate language to each loudspeaker. 60 SOUND &LANGUAGE CONTROL NICAM Reception (In Analogue Mode Only) If the set is equipped with the receiver for NICAM reception, high quality NICAM (Near Instantaneous Companded Audio Multiplex) digital sound can be received. Sound output can be selected according to the type of received broadcast as follows by pressing the I/II button repeatedly. 1 2 When N I C A M m o n o is received, you can select N I C A M M O N O or F M M O N O. When N I C A M stereo is received, you can select N I C A M S T E R E O or F M M O N O. If the stereo signal is weak, switch to F M m o n o. 3 When NICAM dual is received, you can select N I C A M D U A L I, N I C A M D U A L I I or N I C A M D U A L I + I I or M O N O. Speaker Sound Output Selection In AV, Component, RGB and HDMI, DVI mode, you can select output sound for the left and right loudspeakers. Repeatedly press the I / I I button to select the sound output. L+R: Audio signal from audio L input is sent to the left loud speaker and audio signal from audio R input is sent to the right loud speaker. L+L: Audio signal from audio L input is sent to left and right loud speakers. R+R: Audio signal from audio R input is sent to left and right loud speakers. 61 SOUND & LANGUAGE CONTROL ON-SCREEN MENU LANGUAGE / COUNTRY SELECTION The installation guide menu appears on the TV screen when it is switched on for the first time. 1 OK Select your desired language. 2 OK Select your country. * If you want to change Language/ Country selection 1MENU 2 OK Select OPTION. Select Menu Language or Country. 3 OK Select your desired language or country. 4 OK Save. · Press the MENU or EXIT button to close the menu window. · Press the BACK button to move to the previous menu screen. !NOTE G G G G G If you do not finish the set-up Installation Guide by pressing EXIT or if you time out on the OSD (On Screen Display) the installation menu will continuously appear whenever the set is switched on until the set up is completed. If you select the wrong local country, teletext may not appear correctly on the screen and some problems may occur during teletext operation. The CI (Common Interface) function may not be applied based on country broadcasting circumstances. DTV mode control buttons may not function based on country broadcasting circumstances. In countries that Digital broadcasting regulation isn't fixed, some DTV functions may not work depending on digital broadcasting circumstances. 62 SOUND & LANGUAGE CONTROL LANGUAGE SELECTION (IN DIGITAL MODE ONLY) The Audio function allows selection of a preferred language. [. . . ] Sharpness (Command: k k) G To adjust the screen sharpness. 14. Colour Temperature (Command: k u) G To adjust colour temperature. You can also adjust You can also adjust sharpness in the PICTURE menu. Transmission [k][k][ ][Set ID][ ][Data][Cr] Data Min : 00 ~ Max : 64 * Refer to `Real data mapping 1'. [. . . ]