User manual LG M3701C-BAF

[. . . ] Use the screws to secure the stand on the rear side of the product as shown in the diagram. 1 Connecting the Stand cover - Only on some models. 1. The cover may be easily disassembled by pressing up on the base as shown in the figure. Stand cover 2. After connecting the cables, correctly position the stand cover into the holes on the stand. If securely connected, you will hear the latch click into place. 2 Connecting the Speakers - Only on some models. Mount the product onto the speaker by using a screw as shown in the following connect the speaker cable. [. . . ] Function to initialize and release Tile. All Tile setting are released when selecting Tile recall and the screen returns to Full screen. Select the location of the Tile by setting an ID. The image is omitted by the distance between the screens to be naturally shown. · Tile ID · Natural Factory Reset Select this option to return to the default factory settings. 31 User Menus Adjust Set ID and check Serial No. and SW version. Information Set ID Serial No. SW Version MENU Set ID You can assign a unique Set ID NO (name assignment) to each product when several products are connected for display. Specify the number (1~99) using the button and exit. Use the assigned Set ID to individually control each product using the Product Control Program. This menu shows the serial number of the product. This menu shows the software version. Serial No. SW Version 32 Troubleshooting No image is displayed G Is the product power cord connected?If the frequency is out of range, set to the recommended resolution in the Control Panel ­ Display ­ Setting menu. · D-Sub analog signal ­ Press the "AUTO" button in the remote control to automatically select an optimal screen status that fits into the current mode. If adjustment is not satisfactory, use the Clock OSD menu. · D-Sub analog signal ­ Press the "AUTO" button in the remote control to automatically select an optimal screen status that fits into the current mode. If adjustment is not satisfactory, use the Phase OSD menu. · The proper input signal is not connected to the signal port. Connect the signal cable that matches with the source input signal. G Do thin lines appear on the background screen? G Horizontal noise appears or the characters look blurred. G The screen is displayed abnormally. After-image appears on the product. G After-image appears when the product is turned off. · If you use a fixed image for a long time, the pixels may be damaged quickly. Use the screen-saver function. 34 Troubleshooting The audio function does not work. G No sound?· See if the audio cable is connected properly. · See if the sound is set properly. [. . . ] Transmission [f][a][][Set ID][][Data1][][Data2][][Data3][Cr] [Data1] 0 : Monday 1: Tuesday 2 : Wednesday 3 : Thursday 4 : Friday 5 : Saturday 6 : Sunday [Data2] 0H~17H (Hours) [Data3] 00H~3BH (Minutes) Acknowledgement [a][][Set ID][][OK/NG][Data1][Data2][Data3][x] *When reading data, FFH is inputted for [Data1], [Data2] and [Data3]. In other cases, all are treated as NG. L A18 RS-232C Controlling the Multiple Product Transmission / Receiving Protocol 31. On Timer (On/Off Timer) On, Off (Command : F b) Set days for On Timer. Transmission [f][b][][Set ID][][Data1][][Data2][Cr] [Data1] 0 (Write), FFH(Read) [Data2] 00H~FFH bit0 : Monday On Timer On(1), Off(0) bit1 : Tuesday On Timer On(1), Off(0) bit2 : Wednesday On Timer On(1), Off(0) bit3 : Thursday On Timer On(1), Off(0) bit4 : Friday On Timer On(1), Off(0) bit5 : Saturday On Timer On(1), Off(0) bit6 :Sunday On Timer On(1), Off(0) bit7 : Everyday On Timer On(1), Off(0) Acknowledgement [b][][Set ID][][OK/NG][Data1][Data2][x] 32. [. . . ]