User manual LG M4201C-BA

[. . . ] In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. 1 Using the Remote Control Name of the Remote Control Buttons There is not a function which is supported There is not a function which is supported · Power On/Off Button · Input Select Button (See next page) · ARC button To select the image size of the screen. · Auto Button Automatic adjustment function (Operational for the analog signal only) There is not a function which is supported 1 4 7 · CTR. PWR Button Turn on the power of the PC built in the monitor and then turn off. (The CTR. PWR function operates only when the PC Control menu is off. ) · Menu Button · UP and Down buttons Bring up and down direction adjustment. CTR. PWR 2 5 8 0 3 6 9 There is not a function which is supported · Exit Button · Volume Button · Check Button · Mute button * There is not a function which is supported 2 Using the Remote Control · Input Select Button If you press the button once, the following Input Signal Window will appear. [. . . ] * Maximum resolution RGB : 1920 X 1080 @60Hz DVI : 1920 X 1080 @60Hz G Does the 'Power saving mode' On DVI · Connect the RGB cable, and then change the input source to 'RGB'. And then, press the MENU button to set the PC Control value of the SPECIAL menu to 'On'. Disconnect RGB cable, and turn off the power, and then turn on the power again. G Does the 'Check signal cable' message appear?· The signal cable between PC and product is not connected. · Press the 'INPUT' menu in the remote Control to check the input signal. · Press the 'INPUT' menu in the remote Control to check the input signal. G Did you check the INPUT Key? Note * Vertical frequency: To enable the user to watch the product display, screen image should be changed tens of times every second like a fluorescent lamp. The vertical frequency or refresh rate is the times of image display per second. * Horizontal frequency: The horizontal interval is the time to display one vertical line. When 1 is divided by the horizontal interval, the number of horizontal lines displayed every second can be tabulated as the horizontal frequency. The unit is kHz. 25 Troubleshooting The screen image looks abnormal. G Is the screen position wrong at the RGB mode?FAN STOP!" If the power is turned off after this message appears, it means that the fan is out of order. In this case, contact your local service center. 27 Specifications The product specifications can change without prior notice for product improvement. LCD Panel 42 inches visible diagonal (106. 72 cm) TFT (Thin Film Transistor) LCD (Liquid Crystal Display) Panel 0. 681 mm (Pixel Pitch) Rated Voltage Power Consumption AC 100-240V~ 50/60Hz 2. 7A On Mode : 270W Typ. (with PC), 240W Typ. (only Monitor) Sleep Mode : 20W (only Monitor), 60W(with PC), Off Mode : 5W Power Dimensions &Weight H W D Width x Height x Depth 99. 56 cm (39. 19 inches) x 58. 76 cm (23. 13 inches) x 11. 37 cm (4. 47 inches) Net 22. 3 kg (49. 16 lbs) NOTE Information in this document is subject to change without notice. 28 Specifications The product specifications can change without prior notice for product improvement. Video Signal Max. Resolution RGB : 1920 X 1080 @60Hz DVI : 1920 X 1080 @60Hz Recommended Resolution RGB : WUXGA 1920 X 1080 @60Hz DVI : WUXGA 1920 X 1080 @60Hz Horizontal Frequency RGB : 30 - 83 kHz DVI : 30 - 83 kHz 56 - 60 Hz (RGB / DVI) Vertical Frequency Synchronization Type Separate/Composite/Digital 15-pin D-Sub type, DVI (digital), RS-232C Input Connector Environmental Conditions Operational Condition Temperature: 5°C ~ 35°C , Humidity: 10% ~ 80% Storage Condition Temperature: -20°C ~ 60°C , Humidity: 5% ~ 95% NOTE Information in this document is subject to change without notice. 29 Specifications PC Mode ­ Preset Mode Preset mode 1 2 3 4 5 6 7 8 9 640 x 350 720 x 400 640 x 480 800 x 600 1024 x 768 1280 x 720 1280 x 1024 1680 x 1050 1920 x 1080 Horizontal Frequency (kHz) 31. 468 31. 469 31. 469 37. 879 48. 363 44. 772 63. 981 65. 290 66. 587 Vertical Frequency (Hz) 70 70 59 60 60 59 60 59 59 Power Indicator Mode On Mode Sleep Mode Off Mode Product Blue Amber - 30 Specifications VESA wall mounting Connected to another object (stand type and wall-mounted type. ) This product accepts a VESAcompliant mounting interface pad. - (This has to be purchased separately if required. ) For further information, refer to the VESA Wall Mounting Instruction Guide. Kensington Security Slot- (This has to be purchased separately if required. ) Connected to a locking cable that can be purchased separately at most computer stores 31 Specifications Signal Connector Pin Assignment 1 9 17 8 16 24 DVI-D Connector Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Signal(DVI-D) T. Data4+ DDC Clock DDC Data Analog Vertical Sync. Data3+ +5V Power Ground (return for +5V, H. Sync. ) Pin 16 17 18 19 20 21 22 23 24 Signal(DVI-D) Hot Plug Detect T. (Transition Minimized Differential Signaling) 32 Specifications Connecting the USB(Universal Serial Bus) Cable "USB (Universal Serial Bus)" is an innovation in connecting your different desktop peripherals conveniently to your computer. By using the USB, you will be able to connect your mouse, keyboard, and other peripherals to your display instead of having to connect them to your computer. This will give you greater flexibility in setting up your system. USB allows you to connect a chain of up to 120 devices on a single USB port; and you can "hot" plug (attach them while the computer is running) or unplug them while maintaining the Plug and the Plug auto detection and configuration. This display has an integrated BUS-powered USB hub, allowing up to 2 other USB devices to be attached it. 1. [. . . ] Acknowledgement [d][][00][][OK/NG][Data][x] 18. Tile H Position (Command : d e) To set the horizontal position. Transmission [d][e][][Set ID][][Data][x] Data Min : 00H ~ Max : 64H code) L (Hexadecimal Acknowledgement [e][][Set ID][][OK/NG][Data][x] 11 RS-232C Controlling the Multiple Product Transmission / Receiving Protocol 19. Tile V Position(Command : d f) To set the Vertical position. [. . . ]