User manual LG M4214C-BAP

[. . . ] User's Guide M4214C Make sure to read the Safety Precautions before using the product. Keep the User's Guide(CD) in an accessible place for future reference. See the label attached on the product and give the information to your dealer when you ask for service. WARNING -This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Using the Remote Control Name of the Remote Control Buttons · AV Button · Power On/Off Button · Input Select Button (See next page) · ARC button To select the image size of the screen. · Auto Button Automatic adjustment function (Operational for the analog signal only) There is not a function which is supported · Sleep Button When watching AV/S-Video/RGB/HDMI /Component1/ Component2 The product will be automatically turned off after a certain period of time. Press this button repetitively to select an appropriate time duration · PSM Button - Automatically adjusts the image. [. . . ] Programmes with 16:9 format are viewed naturally but 4:3 programmes are magnified on the left and right so that the screen is16:9 format. This pIcture format is 1:1 of general AV. (only RGB PC, HDMI/DVI PC) You can enjoy the picture format of 14:9 or general AV programmes through 14:9 mode. Programmes with 14:9 are viewed naturally, but 4:3 programmes are magnified on the top/bottom and left/right sides. You can enjoy movies on a vast screen through Zoom mode. The 4:3 programmes are magnified on the top/bottom and left/right sides so that screen is 16:9 format. The bottom and top of the picture may be lost. MODE ARC Full Original 4:3 16:9 1:1 14:9 Zoom1, 2 AV Component HDMI/DVI DTV PC DTV RGB PC Spectacle Full Original 4:3 16:9 14:9 Zoom1 Zoom2 1:1 Reset Return Manual config. to the default factory settings. 26 Troubleshooting No image is displayed G Is the product power cord connected?· See if the power cord is properly connected to the outlet. · See if the power switch is turned on. G Power is on, power indicator is blue but · Adjust brightness and contrast again. G Does the 'Out of range' message appear?· If the product is in power saving mode, move the mouse or press any key. · The signal from the PC (video card) is out of the vertical or horizontal frequency range of the product. Adjust the frequency range by referring to the Specifications in this manual. * Maximum resolution RGB : 1920 x 1080 @60Hz HDMI/DVI : 1920 x 1080 @60Hz G Does the 'Check signal cable' message · The signal cable between PC and product is not appear?· Press the 'INPUT' menu in the remote Control to check the input signal. 'Unknown Product' message appears when the product is connected. G Did you install the driver?· Install the product driver, which is provided with the product, or download it from the web site. (http://www. lge. com) · See if the plug&play function is supported by referring to the video card user manual. 'Controls Locked' message appears. G The 'Controls Locked' message appears when pressing the Menu button. · The control locking function prevents unintentional OSD setting change due to careless usage. To unlock the controls, simultaneously press the Menu button and button for several seconds. (You cannot set this function using the remote control buttons. You can set this function in the product only. ) L Note * Vertical frequency: To enable the user to watch the product display, screen image should be changed tens of times every second like a fluorescent lamp. [. . . ] Transmission [m][c][ ][Set ID][ ][Data][Cr] L Data Key code : Refer to page A18. Acknowledgement [c][ ][Set ID][ ][OK][Data][x] A12 RS-232C Controlling the Multiple Product Transmission / Receiving Protocol 20. Tile Mode(Command : d d) Change a Tile Mode. Transmission [d][d][][Set ID][][Data][x] L Data 00 12 13 14 . . . [. . . ]