User manual LG M5201C

[. . . ] User's Guide M5201C Make sure to read the Safety Precautions before using the product. Keep the User's Guide(CD) in an accessible place for future reference. See the label attached on the product and give the information to your dealer when you ask for service. Temporary noise is normal when powering ON or OFF this device. Using the Remote Control Name of the Remote Control Buttons · AV Button · Power On/Off Button · Input Select Button (See next page) · ARC button To select the image size of the screen. · Auto Button Automatic adjustment function (Operational for the analog signal only) There is not a function which is supported · Sleep Button When watching AV/S-Video/RGB/HDMI /Component1/ Component2 The product will be automatically turned off after a certain period of time. Press this button repetitively to select an appropriate time duration · PSM Button - Automatically adjusts the image. Press this button repetitively to set the intended screen. 1 4 7 2 5 8 0 3 6 9 There is not a function which is supported There is not a function which is supported · Menu Button · UP and Down buttons Bring up and down direction adjustment. · Exit Button · Volume Button · Check Button · Mute button * There is not a function which is supported 1 Using the Remote Control · AV Button Each time you press the Input button it will change to AV Component1 Component2 RGB HDMI/DVI · Input Select Button If you press the button once, the following Input Signal Window will appear. [. . . ] You can enjoy movies on a vast screen through Zoom mode. The 4:3 programmes are magnified on the top/bottom and left/right sides so that screen is 16:9 format. The bottom and top of the picture may be lost. MODE ARC Full Original 4:3 16:9 1:1 14:9 Zoom1, 2 AV Component HDMI/DVI DTV PC DTV RGB PC Spectacle Full Original 4:3 16:9 14:9 Zoom1 Zoom2 1:1 Reset Return Manual config. to the default factory settings. 24 Troubleshooting No image is displayed G Is the product power cord connected?· See if the power cord is properly connected to the outlet. · See if the power switch is turned on. G Power is on, power indicator is blue but · Adjust brightness and contrast again. G Does the 'Out of range' message appear?· If the product is in power saving mode, move the mouse or press any key. · The signal from the PC (video card) is out of the vertical or horizontal frequency range of the product. Adjust the frequency range by referring to the Specifications in this manual. * Maximum resolution RGB : 1920 x 1080 @60Hz HDMI/DVI : 1920 x 1080 @60Hz G Does the 'Check signal cable' message · The signal cable between PC and product is not appear?· Press the 'INPUT' menu in the remote Control to check the input signal. 'Unknown Product' message appears when the product is connected. G Did you install the driver?· Install the product driver, which is provided with the product, or download it from the web site. (http://www. lge. com) · See if the plug&play function is supported by referring to the video card user manual. 'Controls Locked' message appears. G The 'Controls Locked' message appears when pressing the Menu button. · The control locking function prevents unintentional OSD setting change due to careless usage. To unlock the controls, simultaneously press the Menu button and button for several seconds. (You cannot set this function using the remote control buttons. You can set this function in the product only. ) L Note * Vertical frequency: To enable the user to watch the product display, screen image should be changed tens of times every second like a fluorescent lamp. The vertical frequency or refresh rate is the times of image display per second. * Horizontal frequency: The horizontal interval is the time to display one vertical line. When 1 is divided by the horizontal interval, the number of horizontal lines displayed every second can be tabulated as the horizontal frequency. The unit is kHz. 25 Troubleshooting The screen image looks abnormal. G Is the screen position wrong? [. . . ] Transmission [m][c][ ][Set ID][ ][Data][Cr] L Data Key code : Refer to page A18. Acknowledgement [c][ ][Set ID][ ][OK][Data][x] A12 RS-232C Controlling the Multiple Product Transmission / Receiving Protocol 20. Tile Mode(Command : d d) Change a Tile Mode. Transmission [d][d][][Set ID][][Data][x] L Data 00 12 13 14 . . . [. . . ]