User manual LG M5203R

[. . . ] Select the signal type you want using the button. 1 4 7 2 5 8 0 3 6 9 Input * Inserting batteries into remote control. 1. Insert the batteries with correct polarity (+/-). · Dispose of used batteries in the recycle bin to prevent environmental pollution. 2 Name and Function of the Parts * The product image in the user's guide could be different from the actual image. Rear View REMOTE CONTROL IN RS-232C (CONTROL& SERVICE) OUT HDMI/DVI IN RGB IN AUDIO (RGB/DVI) COMPONENT IN Y VIDEO PB PR AV IN L-AUDIO-R VIDEO L-AUDIO-R SPEAKER (8) (R) (L) S-VIDEO RGB OUT IN 1 + - + - 2 AV OUT REMOTE CONTROL IN RS-232C (CONTROL& SERVICE) OUT HDMI/DVI IN RGB IN AUDIO (RGB/DVI) COMPONENT IN Y VIDEO PB PR AV IN L-AUDIO-R VIDEO L-AUDIO-R SPEAKER (8) (R) (L) S-VIDEO RGB OUT IN 1 + - + - 2 AV OUT Power Connector : Connect the power cord Wired Remote Control Port RS-232C Serial Ports RGB, HDMI/DVI Ports PC Sound Jack : Connect the audio cable to the *LINE OUT jack of the PC sound card. AV Ports Speaker Ports *LINE OUT A terminal used to connect to the speaker including a built-in amplifier (Amp). [. . . ] Moving the screen position horizontally. Moving the screen position vertically. H-Position V-Position XGA Mode (RGB-PC only). For more improved or better picture quality, select the same mode corresponding to computer resolution. Auto config. XGA Mode ARC Reset 1024x768 1280x768 1360x768 1366x768 23 Selecting and Adjusting the Screen Adjusting Screen CLOCK/PHASE and Position ARC To select the image size of the screen. Spectacle When your AV receives the wide screen signal, it will lead you to adjust the picture horizontally, in a nonlinear proportion, to fill the entire screen. When your AV receives the wide screen signal, it will lead you to adjust the picture horizontally or vertically, in a linear proportion, to fill the entire screen fully. (Europe an version only) When your AV receives the wide screen signal, it will be automatically changed to picture format to be sent. This pIcture format is 4:3 of general AV. You can enjoy movies (the picture format of 16:9) or general TV programmes thorough 16:9 mode. Programmes with 16:9 format are viewed naturally but 4:3 programmes are magnified on the left and right so that the screen is16:9 format. This pIcture format is 1:1 of general AV. (only RGB PC, HDMI/DVI PC) You can enjoy the picture format of 14:9 or general AV programmes through 14:9 mode. The unit is kHz. 25 Troubleshooting The screen image looks abnormal. G Is the screen position wrong?· D-Sub analog signal ­ Press the "AUTO" button in the remote control to automatically select the optimal screen status that fits into the current mode. If adjustment is not satisfactory, use the Position OSD menu. · See if the video card resolution and frequency are supported by the product. If the frequency is out of range, set to the recommended resolution in the Control Panel ­ Display ­ Setting menu. · D-Sub analog signal ­ Press the "AUTO" button in the remote control to automatically select an optimal screen status that fits into the current mode. If adjustment is not satisfactory, use the Clock OSD menu. · D-Sub analog signal ­ Press the "AUTO" button in the remote control to automatically select an optimal screen status that fits into the current mode. If adjustment is not satisfactory, use the Phase OSD menu. · The proper input signal is not connected to the signal port. Connect the signal cable that matches with the source input signal. G Do thin lines appear on the background screen? G Horizontal noise appears or the characters look blurred. G The screen is displayed abnormally. After-image appears on the product. G After-image appears when the product is turned off. [. . . ] 4 : White Wash 8 : Normal L Acknowledgement [p][ ][Set ID][ ][OK][Data][x] A11 RS-232C Controlling the Multiple Product Transmission / Receiving Protocol 18. Auto Configure(Command: j u) To adjust picture position and minimize image shaking automatically. Transmission [j][u][ ][Set ID][ ][Data][Cr] Data 1 : To set Acknowledgement [u][ ][Set ID][ ][OK][Data][x] L 19. Key(Command : m c) To send IR remote key code. [. . . ]