User manual LG M6503C

[. . . ] User's Guide M6503C Make sure to read the Safety Precautions before using the product. Keep the User's Guide(CD) in an accessible place for future reference. See the label attached on the product and give the information to your dealer when you ask for service. Temporary noise is normal when powering ON or OFF this device. Connecting the Speakers - Only on some models. Mount the product onto the speaker by using a screw as shown in the following connect the speaker cable. After installing your speakers, use holders and cable ties to organize the speaker cables. Cable holder Remove the paper. * This feature is not available in all model. Cable tie When the speaker is installed. *Connect the input terminal with a proper color match. * This feature is not available in all model. 1 To install Portrait - Only on some models. "When installing Portrait, rotate it clockwise based on its front. " 2 Using the Remote Control Name of the Remote Control Buttons · AV Button · Sleep Button When watching AV, RGB PC, HDMI/DVI, Component The product will be automatically turned off after a certain period of time. Press this button repetitively to select an appropriate time duration · PSM Button - Toggles through preset video settings. · Power On/Off Button · Input Select Button (See next page) · ARC button Aspect Ratio Correction. · Auto Button Automatic adjustment function (Operational for the analog signal only) There is not a function which is supported There is not a function which is supported There is not a function which is supported · Exit Button · Volume Button Volume up and down · Check Button There is not a function which is supported · Menu Button · UP and Down buttons Bring up and down direction adjustment. · Mute button 3 Using the Remote Control · AV Button Toggles through video AV Component RGB PC HDMI/DVI · Input Select Button If you press the button once, the following Input Signal Window will appear. [. . . ] · The signal from the PC (video card) is out of the vertical or horizontal frequency range of the product. Adjust the frequency range by referring to the Specifications in this manual. * Maximum resolution RGB : 1920 x 1080 @60Hz HDMI/DVI : 1920 x 1080 @60Hz Does the 'Out of range' message appear? Does the 'Check signal cable' message · The signal cable between PC and product is not connected. · Press the 'INPUT' menu in the remote Control to check the input signal. 'UnknownProduct'messageappearswhentheproductisconnected. Did you install the driver?· Install the product driver, which is provided with the product, or download it from the web site. (http://www. lge. com) · See if the plug&play function is supported by referring to the video card user manual. 'Key Lock On' message appears. The 'Key Lock On' message appears when pressing the Menu button. · The control locking function prevents unintentional OSD setting change due to careless usage. To unlock the controls, simultaneously press the Menu button and button for several seconds. (You cannot set this function using the remote control buttons. You can set this function in the product only. ) Note * Vertical frequency: To enable the user to watch the product display, screen image should be changed tens of times every second like a fluorescent lamp. The vertical frequency or refresh rate is the times of image display per second. * Horizontal frequency: The horizontal interval is the time to display one vertical line. When 1 is divided by the horizontal interval, the number of horizontal lines displayed every second can be tabulated as the horizontal frequency. The unit is kHz. 34 Troubleshooting The screen image looks abnormal. Is the screen position wrong?· D-Sub analog signal - Press the "AUTO" button in the remote control to automatically select the optimal screen status that fits into the current mode. If adjustment is not satisfactory, use the Position OSD menu. · See if the video card resolution and frequency are supported by the product. If the frequency is out of range, set to the recommended resolution in the Control Panel "Display" Setting menu. · D-Sub analog signal - Press the "AUTO" button in the remote control to automatically select an optimal screen status that fits into the current mode. If adjustment is not satisfactory, use the Clock OSD menu. · D-Sub analog signal - Press the "AUTO" button in the remote control to automatically select an optimal screen status that fits into the current mode. If adjustment is not satisfactory, use the Phase OSD menu. [. . . ] Transmission [f][g][][Set ID][][Data][Cr] Data 0 : Off 1: On Acknowledgement [g][][Set ID][][OK/NG][Data][x] L L A25 RS-232C Controlling the Multiple Product Transmission / Receiving Protocol 42. Power On Delay (Command : f h) Set the schedule delay when the power is turned on (Unit: second). Transmission [f][h][][Set ID][][Data][Cr] Data : 00H ~ 64H (Data value) · Refer to `Real data mapping' page A8. L L Acknowledgement [h][][Set ID][][OK/NG][Data][x] 43. Language (Command : f i) Set the OSD language. [. . . ]