User manual LG MG-564W

[. . . ] x Do not press buttons with a pointed thing. x Do not pull or bend the wired remote controller cable excessively. x Do not use this wired remote controller for other purpose. x Do not spray an insecticide or other combustible things on the wired remote controller. [. . . ] x Do not give a shock to the wired remote controller or disassemble it by yourself. CAUTION E-2 Contents x VIEW OF THE WIRED REMOTE CONTROLLER x GETTING STARTED x SELECTING THE AUTOMATIC OPERATING MODE x COOLING YOUR ROOM x HEATING YOUR ROOM 4 5 6 8 10 12 14 15 16 18 (EXCEPT COOLING ONLY MODELS) x REMOVING EXCESS HUMIDITY x AIRING YOUR ROOM x ADJUSTING THE AIR FLOW DIRECTION (EXCEPT DUCT TYPE) x SETTING THE ON TIMER x SETTING THE OFF TIMER E-3 ENGLISH View of the Wired Remote Controller The wired remote controller is installed on the wall. Operating mode Removing frost indicator Centralized controller indicator (In case of installing the Centralized controller) Communication error indicator On Timer setting Off Timer setting Test indicator Temperature setting Fan speed Air flow direction Filter Sign indicator On/Off button Temperature adjustment buttons Timer button Timer Set/Cancel button Test button On/Off indicator Fan speed adjustment button Swing button (Except Duct type) Filter Reset button Mode selection button Note x The button is for your installation specialist. x After cleaning the air filter, press the button. Then the wired remote controller will display the FILTER SIGN indicator when the time to clean the air filter. x Duct type air conditioner does not have function of adjusting air flow direction. Therefore, the function is not operated even if you press the button. E-4 Getting Started You have just purchased a wired remote controller and it has been installed by your installation specialist. Your Owner's Instructions contain much valuable information on using your wired remote controller. Please take the time to read them as they will help you take full advantage of the unit's features. In the manual, you will find a series of step-by-step procedures for each function available. The illustrations in the step-by-step procedures use three different symbols: PRESS PUSH HOLD DOWN E-5 ENGLISH Selecting the Automatic Operating Mode In the Automatic mode, the room temperature and the fan speed are controlled automatically. 1 If necessary, press (ON/OFF) button. Result: : x The On/Off indicator on the wired remote controller comes on. x The air conditioner runs in the mode selected when the unit was last used. IMPORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: x Plugged in x Stopped lt will start up normally after three minutes. 2 To select the AUTO mode, press the button until is displayed at the top of the wired remote controller. Result: : x The air conditioner runs in the AUTO mode. Note x You can change modes at any time. E-6 3 To adjust the temperature, press the buttons one or more times until the required temperature is displayed. Possible temperatures are between 18C and 30C inclusive. Result: : x Each time you press buttons: - The temperature is adjusted by 1C. x The air conditioner starts removing the excess humidity. The quantity of air is adjusted automatically. 4 To control the direction of the air flow, refer to page 15. E-13 ENGLISH Airing Your Room If the atmosphere in your room is stale, you can air it using the FAN feature. 1 If necessary, press (ON/OFF) button. Result: : x The On/Off indicator on the wired remote controller comes on. x The air conditioner runs in the mode selected when the unit was last used. IMPORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: x Plugged in x Stopped It will start up normally after three minutes. 2 To select the FAN mode, press the button until is displayed at the top of the wired remote controller. Result: : x The air conditioner runs in the FAN mode. Note x You can change modes at any time. 3 Select the fan speed by pressing the button one or more times until the intended value is displayed: Low Medium High 4 To control the direction of the air flow, refer to page 15. E-14 Adjusting the Air Flow Direction (Except Duct Type) ENGLISH Depending on the position of the indoor unit, you can adjust the position of the air flow blade, thus increasing the efficiency of the air conditioner. 1 Press the button. Result: The blade is moving between up and down. IMPORTANT When the air conditioner is first turned on, the blade is moved. 2 To stop the blade, press the button again. To set to the required position, press the button again when the blade is in the required position. E-15 Setting the On Timer The On Timer enables you to switch on the air conditioner automatically after a given period of time. You can set the period of time from 30 minutes to 24 hours. You can select the On Timer only when the air conditioner is off. 1 To set the operating time, press the button one or more times until the required time is displayed. [. . . ] You can select the On Timer only when the air conditioner is off. 1 To set the operating time, press the button one or more times until the required time is displayed. Possible time is between 0. 5 hour and 24 hours inclusive. 2 Press the Result: button to complete the setting. x Blinking of the timer indicator stops. x The selected mode and the temperature disappear on the display after 5 seconds. [. . . ]