User manual LG MG-604WS

[. . . ] N When moving, consult authorized service personnel for disconnection and installation of the unit. N Do not become over-exposed to cold air by staying in the direct path of the air flow of the air conditioner for extended periods of time. N Do not insert fingers or objects into the outlet port or intake grilles. N Do not start and stop air conditioner operation by disconnecting the power supply cord and so on. [. . . ] button. Note E-9 Cooling Your Room You must select the Cool mode if you wish to adjust the: N Cooling temperature N Fan speed when cooling 1 If necessary, press the Result: (On/Off) button. N The operation indicator on the indoor unit lights up. N The air conditioner starts up in the mode selected when the unit was last used. The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: N Plugged in N Stopped lt will start up normally after three minutes. IMPORTANT 2 If the is not displayed at the top of the remote control, press the button on the remote control one or more times until it appears. Result: N The indoor unit beeps each time you press the N The air conditioner runs in COOL mode. button. Note 3 To adjust the temperature, press the button one or more times until the required temperature is displayed. Possible temperatures are between 18C and 30C inclusive. Result: N Each time you press the button: - The temperature is adjusted by 1C - The indoor unit beeps N The air conditioner starts cooling, provided that the room temperature is higher than the selected temperature. N If the room temperature reaches the set temperature, the air conditioner stops cooling, but the fan is still operating. 4 Select the fan speed by pressing the until the required setting is displayed: Automatic (rotated : Low Medium High Result: Each time you press the beeps. button one or more times ) button, the indoor unit 5 To control the direction of the air flow, refer to pages 16 and 17. E-10 Changing the Room Temperature Quickly ENGLISH The Turbo cooling function is used to cool your room as quickly as possible. Example : You have just come home and find that the room is very hot. You wish to cool it down as quickly as possible. The Turbo function operates for 30 minutes with the maximum settings before returning automatically to the mode and temperature previously selected. 1 If necessary, press the Result: (On/Off) button. N The operation indicator on the indoor unit lights up. Set to the initial position powered. E-16 Adjusting the Air Flow Direction Horizontally ENGLISH There are two sets of inner air flow blades. Just as the outer air flow blade can be adjusted vertically, the inner blades can be adjusted horizontally. 1 Adjust each set of inner blades to the required position, by pushing or pulling them sideways. E-17 Setting the On Timer The On Timer enables you to switch on the air conditioner automatically after a given period of time. You can set the period of time from 30 minutes to 24 hours. 1 To set the operating time, press the button one or more times until the required time is displayed. Possible time is between 0. 5 hour and 24 hour inclusive. 2 Press the Result: (Set/Cancel) button to complete the setting. N Blinking of the timer indicator stops. N The selected mode and the temperature on the display disappear after 10 seconds. N The air conditioner will switch on automatically when the counter displayed on the remote control reaches the set time and disappears the On timer setting. 3 To select an operating mode in advance, press the button until the desired mode is displayed at the top of the remote control. Result: N The air conditioner will run in the selected mode when it is turned on. To Cancel the On Timer Press the Note (Set/Cancel) button. N If you press the button when the Off Timer is set, the Off Timer is also cancelled. E-18 Setting the Off Timer ENGLISH The Off Timer enables you to switch off the air conditioner automatically after a given period of time. [. . . ] They may save you the time and expense of an unnecessary call. Problem The air conditioner does not operate at all Explanation/Solution N Check that the breaker used for the air conditioner is switched on. N Check that the operation indicator on the indoor unit is on; if necessary press the (On/Off) button on the remote control. N Check whether the TIMER indicator on the indoor unit is switched on. [. . . ]