User manual LG MS-24AH ST0

[. . . ] In case you use another power cord, make sure that it is certified by the applicable national standards if not being provided by the supplier. If the power cable is faulty in any way, please contact the manufacturer or the nearest authorized repair service provider for a replacement. The appliance coupler is used as the disconnect device. Please make sure the device is installed near the wall outlet to which it is connected and that the outlet is easily accessible. [. . . ] Tie down the base lock to perpendicularity direction. Once assembled take the monitor up carefully and face the front side. Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. 4 Connecting the Display Disassembling the stand 1. Place the monitor with its front facing downward on a soft cloth. Stand Base Head 2. Turn the Cable holder in the direction of the arrow shown below to remove it. Cable holder 3. Change your lock on the product as it follows and turn it in the arrow direction. If you can't release the stand base even the locking knob is at a release position, Please push the indicated knob down and retry it. 5 Connecting the Display 4. Pushing the PUSH button, take the stand base from stand body. Warning: You can hurt your finger. Good Position Bad Position 6 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5° to 20° When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body. You can hurt your finger(s). Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. 7 Connecting the Display Connecting to the Computer 1. You can unlock the OSD controls at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" should appear. 11 Control Panel Functions ( ) SOURCE Use these buttons to select or adjust functions in the On Screen Display. Use this button to make either D-SUB or LAN connector active. This feature is used when two input sources are connected to the display. ( ) VOLUME Use these buttons to select or adjust functions in the On Screen Display. Use buttons to decrease or increase the speaker volume on LAN input. AUTO/SET Button Use this button to enter a selection in the On Screen Display. AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the AUTO/SET button before entering the On Screen Display(OSD). Power Button · D-SUB : Use this button to turn the display on or off. · LAN Monitor OFF: Press the power button and press it again to turn off the power, or wait 10 second. LAN(Clint) OFF: Press the power button and the AUTO/SET button to turn off the power of LAN input. ON : Press the power button to turn on the power. Power Indicator This Indicator lights up blue when the display operates normally(On Mode). If the display is in Sleep Mode (Energy Saving), this indicator color changes to flicker. 12 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making image adjustments. To make adjustments in the On Screen Display, follow these steps: MENU AUTO/SET MENU Press the MENU Button, then the main menu of the OSD appears. [. . . ] If the results are unsatisfactory, decrease the horizontal bars using the PHASE icon in the on screen display. · Check Control Panel --> Display --> Settings and adjust the display to the recommended resolution or adjust the display image to the ideal setting. Set the color setting higher than 24 bits (true color). (Only for D-SUB input) G Any horizontal noise appearing in any image or characters are not clearly portrayed. Important Check Control Panel --> Display --> Settings and see if the frequency or the resolution were changed. If yes, readjust the video card to the recommend resolution. [. . . ]