User manual LG N1941W

[. . . ] ENGLISH OWNER'S MANUAL NETWORK MONITOR Please read this manual carefully before operating your set and retain it for future reference. NETWORK MONITOR MODEL N194WA www. lg. com Accessories Thank you for purchasing this LGE product Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. OWNER'S MANUAL /Cards 15-pin D-SUB Signal Cable (To set it up, this signal cable may be attached to this product before shipping out. ) Power Cord (Depending on the country) USB Extension Cable IMPORTANT This accessories may look different from those shown here. User must use shielded signal interface cables (D-SUB 15 pin cable) with ferrite cores to maintain standard compliance for the product. Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. [. . . ] Turn the Cable holder in the direction of the arrow shown below to remove it. Cable holder 3. Change your lock on the product as it follows and turn it in the arrow direction. If you can't release the stand base even the locking knob is at a release position, Please push the indicated knob down and retry it. 5 Connecting the Display 4. Pushing the PUSH button, take the stand base from stand body. Warning: You can hurt your finger. Good Position Bad Position 6 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5° to 20° When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body. You can hurt your finger(s). Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. 7 Connecting the Display Connecting to the Computer 1. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. A Connect D-SUB(RGB Analog) Cable (PC) B Connect D-SUB(RGB Analog) Cable (Mac) signal input cables Wall-outlet type Mac adapter (This item must be purchased separately. ) For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-SUB VGA connector on the supplied cable to a 15 pin 2 row connector. Connect the signal input cable and tighten it up by turning in the direction of the arrow as shown in the figure. NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. When connecting the D-SUB cable with the LAN cable, connect the D-SUB cable first. Then, connect the LAN cable and other signal input cables. 2. Press button on the front switch panel to turn the power on. When monitor power is turned on, the 'Self Image Setting Function' is executed automatically on D-SUB input. NOTE ` Self Image Setting Function'?This function provides the user with optimal display settings. When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for D-SUB input signals. When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted screen while using the device or after changing screen resolution, press the AUTO/SET function button to improve resolution. 8 Connecting the Display Connecting to the Computer Using LAN 1. Make sure to turn off the computer and product. Connect the cable as below sketch map form 1 to 2 . A Connect peripheral devices B Connect LAN Cable USB 1. 1 port (Only for keyboard and mouse) USB 2. 0 port (Only for USB memory stick) signal input cables Wall-outlet type switch hub Host LAN Cable Type - Standard : IEEE 802. 3 ETHERNET ISP (Internet Service Provider) Network Monitor Keyboard/Mouse Input LAN cable should be connected before booting PC. (This item must be purchased separately. ) Headphone/Earphone Input Automatically mutes the speaker volume when the headphones are plugged in. For an angle plug earphone/microphone, it is difficult connect it with a peripheral device, so use a straight type. Angle type Straight type Connect the USB extension cable to the USB 2. 0 port for more convenient use. When connecting the D-SUB cable with the LAN cable, connect the D-SUB cable first. Then, connect the LAN cable and other signal input cables. 2. Press button on the front switch panel to turn the power on. When you use the monitor speaker via the LAN, turn the PC volume up to the highest level and adjust the monitor volume. When you encounter problems such as blurry screen, blurred letters, screen flicker or titled screen while using the device or after changing screen resolution, press the AUTO/SET function button to improve resolution. 9 Connecting the Display To arrange the cables Connect the power cord and the signal cable as shown in the figure and then fix them to the cable holder. 1. Open the cable holder and fix the cables inside the Cable holder. Cable holder NOTE This picture shows how to organize cables generally and may look different from your product. 10 Control Panel Functions Front Panel Controls MUTE Button · LAN : This menu is available, use this button to switch the sound on or off. or <mute off> · D-SUB : This menu is not available. [. . . ] The setting method can differ by computer and O/S (Operation System), and resolution mentioned above may not be supported by the video card performance. In this case, please ask to the computer or the video card manufacturer. If the recommended resolution (optimal resolution) is not selected, letters may be blurred and the screen may be dimmed, truncated or biased. Make sure to select the recommend resolution. 21 Troubleshooting Display image is incorrect G The screen color is mono or abnormal. [. . . ]