User manual LG N2200P

[. . . ] In case you use another power cord, make sure that it is certified by the applicable national standards if not being provided by the supplier. If the power cable is faulty in any way, please contact the manufacturer or the nearest authorized repair service provider for a replacement. The appliance coupler is used as the disconnect device. Please make sure the device is installed near the wall outlet to which it is connected and that the outlet is easily accessible. [. . . ] Make the monitor stand , then pull out the Stop Pin. Warning: The tape and locking pin may only be removed from those monitors equipped with a standing base when the base is pulled up. Otherwise, you may be injured by the protruding sections of the stand. pull out the stop pin Stop Pin Stop Pin Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. 4 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range: -6° to 17° -6° 17° Height Range: maximum 4. 33 inch (110. 0 mm) 110. 0 mm First, remove the locking pin. Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. 5 Connecting the Display Using the Pivot function -The pivot function allows you to rotate the screen 90 degrees clockwise. 1. Lift the monitor to its highest height to utilize the Pivot function. Landscape & Portrait : You can rotate the panel 90 o clockwise. Please be cautious and avoid contact between the monitor head and the Stand Base when rotating the screen to access the Pivot function. If the monitor head touches the Stand Base, then the Stand Base could crack. Head section Stand section 3. Be careful with the cables when rotating the screen. 6 Connecting the Display Connecting to the Computer 1. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. A Connect D-SUB(RGB Analog) Cable (PC) Connect the signal input cable and tighten it up by turning in the direction of the arrow as shown in the figure. The message "OSD UNLOCKED" should appear. 10 Control Panel Functions ( ) SOURCE Use these buttons to select or adjust functions in the On Screen Display. Use this button to make either D-SUB or LAN connector active. This feature is used when two input sources are connected to the display. ( ) VOLUME Use these buttons to select or adjust functions in the On Screen Display. Use buttons to decrease or increase the speaker volume on LAN input. AUTO/SET Button Use this button to enter a selection in the On Screen Display. AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the AUTO/SET button before entering the On Screen Display(OSD). Power Button · D-SUB : Use this button to turn the display on or off. · LAN Monitor OFF: Press the power button and press it again to turn off the power, or wait 10 second. LAN(Clint) OFF: Press the power button and the AUTO/SET button to turn off the power of LAN input. ON : Press the power button to turn on the power. Power Indicator This Indicator lights up blue when the display operates normally(On Mode). If the display is in Sleep Mode (Energy Saving), this indicator color changes to flicker. 11 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making image adjustments. To make adjustments in the On Screen Display, follow these steps: MENU AUTO/SET MENU Press the MENU Button, then the main menu of the OSD appears. To access a control, use the or Buttons. [. . . ] If the results are unsatisfactory, decrease the horizontal bars using the PHASE icon in the on screen display. · Check Control Panel --> Display --> Settings and adjust the display to the recommended resolution or adjust the display image to the ideal setting. Set the color setting higher than 24 bits (true color). (Only for D-SUB input) G Any horizontal noise appearing in any image or characters are not clearly portrayed. Important Check Control Panel --> Display --> Settings and see if the frequency or the resolution were changed. If yes, readjust the video card to the recommend resolution. [. . . ]