User manual LG N224WHA-BS

[. . . ] ENGLISH OWNER'S MANUAL NETWORK MONITOR Please read this manual carefully before operating your set and retain it for future reference. NETWORK MONITOR MODEL N224WHA www. lg. com Accessories Thank you for purchasing this LGE product Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. OWNER'S MANUAL /Cards 15-pin D-SUB Signal Cable (To set it up, this signal cable may be attached to this product before shipping out. ) Or Power Cord AC-DC adapter (Depending on the country) AC-DC adapter (Depending on the country) USB Extension Cable IMPORTANT This accessories may look different from those shown here. User must use shielded signal interface cables (D-SUB 15 pin cable) with ferrite cores to maintain standard compliance for the product. Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. [. . . ] Adjust the position of the panel in various ways for maximum comfort. Tilt Range: -6° to 17° -6° 17° Height Range: maximum 4. 33 inch (110. 0 mm) 110. 0 mm First, remove the locking pin. Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. 5 Connecting the Display Using the Pivot function -The pivot function allows you to rotate the screen 90 degrees clockwise. 1. Lift the monitor to its highest height to utilize the Pivot function. Landscape & Portrait : You can rotate the panel 90 o clockwise. Please be cautious and avoid contact between the monitor head and the Stand Base when rotating the screen to access the Pivot function. If the monitor head touches the Stand Base, then the Stand Base could crack. Head section Stand section 3. Be careful with the cables when rotating the screen. 6 Connecting the Display Connecting to the Computer 1. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. A Connect D-SUB(RGB Analog) Cable (PC) Connect the signal input cable and tighten it up by turning in the direction of the arrow as shown in the figure. signal input cables Wall-outlet type When using a D-Sub signal input cable connector for Macintosh OR Wall-outlet type Mac adapter : For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) Dsub VGA connector on the supplied cable to a 15 pin 2 row connector. NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. When connecting the D-SUB cable with the LAN cable, connect the D-SUB cable first. Then, connect the LAN cable and other signal input cables. 2. Press button on the front switch panel to turn the power on. When monitor power is turned on, the 'Self Image Setting Function' is executed automatically on D-SUB input. NOTE ` Self Image Setting Function'?This function provides the user with optimal display settings. When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for D-SUB input signals. When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted screen while using the device or after changing screen resolution, press the AUTO/SET function button to improve resolution. 7 Connecting the Display Connecting to the Computer Using LAN 1. Make sure to turn off the computer and product. Connect the cable as below sketch map form 1 to 2 . A Connect peripheral devices B Connect LAN Cable USB 1. 1 port (Only for keyboard and mouse) USB 2. 0 port (Only for USB memory stick) Wall-outlet type OR signal input cables Wall-outlet type switch hub LAN Cable Type - Standard : IEEE 802. 3 ETHERNET Host ISP (Internet Service Provider) Network Monitor Keyboard/Mouse Input LAN cable should be connected before booting PC. (This item must be purchased separately. ) Headphone/Earphone Input Automatically mutes the speaker volume when the headphones are plugged in. NOTE For an angle plug earphone/microphone, it is difficult connect it with a peripheral device, so use a straight type. Angle type Straight type Connect the USB extension cable to the USB 2. 0 port for more convenient use. When connecting the D-SUB cable with the LAN cable, connect the D-SUB cable first. Then, connect the LAN cable and other signal input cables. 2. Press NOTE button on the front switch panel to turn the power on. When you use the monitor speaker via the LAN, turn the PC volume up to the highest level and adjust the monitor volume. When you encounter problems such as blurry screen, blurred letters, screen flicker or titled screen while using the device or after changing screen resolution, press the AUTO/SET function button to improve resolution. 8 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display Using the cable holder 1 2 3 9 Control Panel Functions Front Panel Controls MUTE Button · LAN : This menu is available, use this button to switch the sound on or off. [. . . ] The setting method can differ by computer and O/S (Operation System), and resolution mentioned above may not be supported by the video card performance. In this case, please ask to the computer or the video card manufacturer. If the recommended resolution (optimal resolution) is not selected, letters may be blurred and the screen may be dimmed, truncated or biased. Make sure to select the recommend resolution. 20 Troubleshooting Display image is incorrect G The screen color is mono or abnormal. [. . . ]